قناة عامة / جداول المواصفات

باوتك اتش بي: مطاط مقاوم للماء ومضاد للماء
طلاء الحماية على أساس تشتت البولي يوريثين (PUD)

المشاركة على مواقع التواصل الاجتماعي

مشاركة الرابط

استخدام رابط دائم للمشاركة في وسائل الاعلام الاجتماعية

المشاركة مع صديق

برجاء تسجيل الدخول لإرسال هذا document بالبريد الالكتروني!

تضمين في موقعك

Select Link to start with 

BAUCOAT HP

Elastomeric Waterproof & Protective Coating Based

on Polyurethane Dispersion (PUD)

DESCRIPTION

BAUCOAT HP is a liquid applied elastomeric

waterproof and protective coating based on

polyurethane dispersion (PUD)

The polyurethane is modified with specially

selected polymers to form a tough, flexible and

durable coating. It is completely free of

hazardous ingredients.

TYPICAL USES

Waterproofing or vapor barrier protection of

exposed roofs, domes, terraces, balconies,

corrugated sheets and wet areas like kitchens,

bathrooms & toilets

ADVANTAGES

• Ready to use / apply single component

product

• Forms a highly elastomeric, tough and

resilient membrane.

• Environment friendly

• Fast surface hardness, no tack surface, low

dirt pick-up.

• Excellent crack bridging properties

• Exhibits high resistance to weather

conditions and good resistance to UV

radiation

• Good adhesion and elastic recovery.

Excellent resistance to water and vapor.

• Good chemical resistance against diluted

acids, oil, salts, bacteria and common fuels.

TECHNICAL PROPERTIES

Color White, Green, Grey (As

per requirements)

Solid Content [%] > 60

SRI (Solar Reflective Index) > 80 (White)

Elongation [%] 400 (+/- 30)

Tensile Strength [N/mm²] 2 (+/- 0.2)

Pull Off Adhesion [N/mm²]

(at concrete failure) 1.20

Peel Off Adhesion [N/mm] 2.0

Crack Bridging [mm] 1.5

Hydrostatic Pressure @ 5bar (60m) No leakage

Chemical Resistance Dilute acids & alkalis,

sea water

Full cure [days] 7

Application Temperature [°C]5 to 35

Service Temperature [°C] -20 to 70

(The properties shown below were obtained under

laboratory conditions).

All values given are subject to 10% tolerance

APPLICATION INSTRUCTION

Surface Preparation

Surfaces must be cleaned and made free of dust,

dirt, moss, oil, grease and other loose particles.

This can be achieved by grit/sand/shot blasting.

As a minimum, vigorous wire brushing should be

employed. All pin holes and surface defects shall

be repaired with a suitable concrete repair

mortar.

Priming

BAUCOAT HP does not require priming as such

and can directly be applied onto the substrate

surface. In case of highly porous surface, a

priming coat is recommended to seal the pores

and stabilize the surface.

The primer coat can be produced on site by

diluting BAUCOAT HP with water (20% by

weight) . Apply the primer coat @ 4m²/ Kg and

allow to dry.

The primer coat also functions as an adhesion

promoter for the top coats. It can be applied by

a brush, roller or airless spray and allowed to dry

completely before the application of subsequent

coats.

Mixing

BAUCOAT HP is a single component product but

mix the contents of the pail thoroughly prior to

application to remove any sediment. A slow

speed drill and suitable paddle mixer shall be

used to avoid the formation of air bubbles.

Application

The coating can be applied with a brush, roller or

airless spray and shall be applied in a minimum

of 2 coats. Apply the first coat of undiluted

material at a coverage rate of 1kg/m2

/coat to

get an approximate dry film thickness of 0.5 mm.

It is important to ensure that each coat is

completely cured before applying subsequent

coats. The second coat should be applied at right

angle to the first at the same coverage rate, to

ensure a full unbroken coating to the substrate.

CURING

BAUCOAT HP will achieve its full strength after a

curing period of 7 days.

PACKAGING

25 Kg Pails & 200 Kg Drum

COVERAGE

1Kg /m² at 0.5 mm thickness.

Two coats will give a combined thickness of 1mm

STORAGE & SHELF LIFE

Store under cover, out of direct sunlight, clear of

the ground on pallets and protect from extreme

temperatures. In tropical climate the product

must be stored in air-conditioned environment

(<25ºC).

Shelf life is 12 months when stored as above.

PRECAUTIONS

As with all construction chemicals products

caution should always be exercised. Protective

clothing such as gloves and goggles shall be

worn.

Treat any splashes to the skin or eyes with fresh

water immediately. Should any of the products

be accidentally swallowed, do not induce

vomiting, but call for medical assistance

immediately. There are no known health hazards

associated with BAUCOAT HP.

Clean all the tools with water after use.

Hardened materials can be removed

mechanically only. Allow the waste to cure. Seal

it into a suitable container and bury in landfill as

per local regulations.

BAUCOAT HP

Highly Elastomeric Acrylic Waterproofing & Protective Coating

1. Product Description

BAUCOAT HP is single component highly elastomeric, acrylic waterproofing and

protective coating.

2. Substrate Requirement

• All surfaces must be structurally sound, clean, free from dust, oil and any traces of

foreign materials that may affect adhesion of the waterproof coating on the

substrate. •

• Brick, block and concrete walls/ floors must be allowed to cure for a minimum of 4

weeks prior to application of BAUCOAT HP.

• Cement render and screed must be allowed to cure for at least 7 days and finished

to semi-smooth finish with a wood float. After curing, a thorough check on the

soundness in adhesion of the screed and render should be carried out. All

substrate defects should be properly rectified.

• Painted surface must be scrapped to expose the original substrate for the

waterproofing application.

• The trueness of the background surface required for the substrate beds should be

such that, when checked with a 2m straightedge, any gap under the straightedge

between points of contact does not exceed 3mm.

• Thoroughly dampen the substrate with water and allow access to drain away.

• Incase of metal substrate, rust scales to be removed using wire brush.

• Ensue a minimum slope of 1 in 100 is already provided

3. Application of BAUCOAT HP

• Make sure that all substrate requirements are met, such as temperature, moisture

content of the prepared substrate (preferably below 5%) etc.

• Mix the bucket/drum thoroughly prior to application to remove the sediments.

• Dilute BAUCOAT HP with 20% water to be used as primer coat on the substrate

and allow it to dry for about 3-4 hours.

• Once the surface is dry, clean the surface and apply BAUCOAT HP at 1 kg per

square meter. For spray application, dilute BAUCOAT HP with 5% of water to

reduce the viscosity.

• Allow the surface to dry for 4-5 hours.

• Apply the second coat at 1 kg per square meter in right angle to the first coat.

• Allow the coating to cure fully for 72 hours to achieve its full properties.

• Once the coating is cured completely, it should be checked for its adhesion to the

substrate. For this mark a square of 5cm x 5cm randomly on the surface.

• Cut the square with a knife diagonally across the square. Rip the coating and check

the thickness with Vernier calipers, to see if the dry film has an average thickness

of 1mm.

• Once these tests are done, reapply BAUCOAT HP over those portions, in

accordance with the regular procedure.

4. Post Application

• Conduct ponding test by filling up to 50mm of water for 48 hours to ensure leak

free terrace.

Material Safety Data Sheet

BAUCOAT HP

1) PRODUCT AND COMPANY IDENTIFICATION Distributed by: BAUTECH Chemical Industries LLC

Tel: +971-67441150 Fax: +971-67441120

P.O. Box 23054, Ajman, United Arab Emirates

Web: www.bautechindustries.com

2) COMPOSITION / INFORMATION ON INGREDIENTS

Chemical characterization Acrylic Emulsion (CAS No.25085-34-1) Water (CAS No,

7732-18-5) Pigments & additives.

Hazardous ingredients N/A. Ingredients deemed non hazardous

Chemical name HS CODE: 3209.1090

3) POTENTIAL HAZARDS

Primary hazard Non-Flammable & Non Toxic

Secondary hazard May be irritant to skin and eyes contact

4) FIRST AID MEASURES

Inhalation N/A

Eye Contact Wash with plenty of water for at least 15 minutes. If

irritation persists, seek medical attention.

Skin Contact Remove contaminated clothing and wipe affected skin

with dry cloth then wash with soap and water. Seek

medical attention if irritation persists.

Ingestion DO NOT INDUCE VOMITING because of risk of aspiration.

Give 200-300mls (half pint) of water to drink. Seek

immediate medical attention.

NOTE TO PHYSICIANS. Treat observation and supportive measures as indicated

by the patient’s conditions. See section 11 Toxilogical

information.

5) FIRE FIGHTING MEASURES

Extinguishing Media N/A Non flammable

Not to be used None

Combustion products N/A

6) ACCIDENTAL RELEASE MEASURES

Personal Protection during Spill Wear goggles, gloves and overalls. Spillage causes

slippery surfaces.

Precautions to Protect Environment Prevent ingress to drains and water-courses. If polluted

water enters water-courses inform relevant authorities

immediately.

Spillage Clean Up Methods Absorb spillage with earth or sand.

After spillage / leakage Take up with an absorbent material e.g. sand, sawdust

and collect in a disposal bags.

Please refer to local rules and regulations for disposal.

7) HANDLING AND STORAGE

Usage Precautions Ensure adequate ventilation. Avoid contact with the eyes

and skin. When using DO NOT eat, drink or smoke.

Storage Criteria Keep in cool ventilated area. Keep containers sealed.

8) EXPOSURE CONTROLS / PERSONAL PROTECTION

INGREDIENT. Blend of Water, Styrene Acrylic co polymer pigments and

additives.

CAS No. Acrylic Emulsion (CAS No.25852-37) Water (CAS No,

7732-18-5)

Personal Protective Equipment Wear goggles giving complete eye protection. Wear nitrile

gloves. In cases of insufficient ventilation wear selfcontained respiratory equipment.

Hygienic Work Routines Keep working clothes separate and do not take home.

Use good personal hygiene practices. Wash hands after

handling product.

9) PHYSICAL AND CHEMICAL PROPERTIES

Form Thixotropic Paste

Color Milky White

Odor Aromatic

Change in physical state No statement possible

Density 1.25 +/- 0.02 kg/ltr

Vapor pressure, mbar (°C) N/A

Solubility in water Water soluble

pH 6 to 9

Boiling Point, °C 100 0 C

Flash Point N/A

Ignition temperature N/A

Thermal decomposition N/A

Explosion limits N/A

VOC content 25 g/lit.

10 STABILITY AND REACTIVITY

Stability Stable under normal conditions.

Materials to Avoid N/A.

Conditions to avoid in use N/A

Hazardous reactions N/A

11) INFORMATION ON TOXICITY

Skin Contact Prolonged skin contact will cause irritation.

12) INFORMATION ON ECOLOGICAL EFFECTS

Environmental Hazards Harmful to aquatic organisms. (R52). May cause harmful

effects to aquatic environment. (R53).

Degradability Not readily biodegradable

13) DISPOSAL

Disposal This product and its container must be disposed of as a

hazardous waste. DO NOT empty into drains or

waterways.

14) TRANSPORT

DOT : Not restricted.

TDG : Not restricted for road or rail.

ICAO : Not restricted

IATA : Not restricted

IMDG/IMO : Not restricted

Other Information Regarded as non- hazardous for transport.

15) REGULATIONS

Labelling clear indication and identification of materials

Symbol None

R Phrases May cause sensitization to skin contact

S Phrases After contact with skin, wash immediately with water

and soap. Wear suitable PPE’s for protection.

16) FURTHER INFORMATION Whilst the descriptions, designs data and information

contained herein are presented in good faith and

believed to be accurate, it is provided for your guidance

only. Because many factors may affect processing or

application/use, we recommend that you make tests to

determine the suitability of a product for your particular

purpose prior to use. No warranties of any kind, either

expressed or implied, including warranties of

merchantability or fitness for a particular purpose, are

made regarding products described or designs, data or

information set forth, or that the products, designs, data

or information may be used without infringing the

intellectual property rights of others. In no case shall the

descriptions, information, data or designs provided be

considered a part of our terms and conditions of sale.

Further you expressly understand and agree that the

descriptions, data and information given or results

obtained, all such being given and accepted at your risk.

Approved:

MSDS VERSION: 01

Date: MAY 2018 Last Revision: MAY 2019

طرق العرض

  • 3297 عدد المشاهدات
  • 2587 موقع المشاهدات
  • 710 المشاهدات المدمجة

الإجراءات

  • 0 مشاركات اجتماعية
  • 3
  • 0
  • 0تعليقات

عدد المشاركات

  • 0  فيسبوك
  • 0  توتير
  • 0  ينكدين

يتضمن 3

  • 16 161.97.92.48
  • 102 www.sab-us.com
  • 1 www.google.com

زوار الموقع 370402