1. w Ü rth sealants & a dhesives Product Range Catalogue 2013

3. contents d escription p icture p age Silicones 1-15 Bitumen Mastics 16 Acrylic Sealants UPVC & All Weather Sealants 17-19 Panel Adhesives Gripfill, PinkGrip & Stixall Mirror Adhesives 20-26 Fire Cements Intumescent Sealants 27-29 PU Sealers (Polyurethane) Spray Sealer 30-35 Polyurethane Foams (Gun Foam) 36-42 Wood Glues PVA & PUR Smart Tack 43-49 Super Glues Contact Adhesives Rubber Glue 50-55 Windscreen Adhesives 56-59 d escription p icture p age Epoxy Resins Plastic Repair 60-64 Thread Lock & Pipe Sealants Flange Sealants 65-74 Adhesive Tapes 75-81 P.T.F.E Tapes 82-83 Gasket Sealers 84-85 Exhaust Paste 86 Chemical Anchor 87 Liquid Metal Putty Repair Sticks 88-89 Adhesive Cleaner 90 Retro-reflective warning marking Tarp Repair Kit 91-92 contents

13. 10 s ilicone product data These figures are only intended as a guide and should not be used in preparing specifications Typical general characteristics Inspection Method Value Unvulcanized rubber Density at 20 °C DIN 51757 1,01 g/cm³ Consistency ISO 7390 non-sag Extrusion rate at 23 °C 300 ml/min Skin forming time at 23 °C / 50 % r.h. approx. 35 min Curing at 23 °C / 50 % RLF approx. 2 mm/day Vulcanized rubber After 4 weeks ́storage at 23°C / 50 % r.h. Tensile strength ISO 8339 0,7 N/mm 2 Elongation at break ISO 8339 300 % Modulus at 100 % elongation ISO 8339 0,37 N/mm² Hardness Shore A ISO 868 24 Movement capability ISO 11600 25 % Tear strength ISO 34, method C 4,5 N/mm

15. 12 s ilicone product data These figures are only intended as a guide and should not be used in preparing specifications Typical general characteristics Inspection Method Value Unvulcanized rubber Density at 20 °C DIN 51757 0.99 g/cm³ Consistency ISO 7390 non-sag Extrusion rate at 23 °C 400 ml/min Skin forming time at 23 °C / 50 % r.h. approx. 35 min Curing at 23 °C / 50 % RLF approx. 2 mm/day Vulcanized rubber After 4 weeks ́storage at 23°C / 50 % r.h. Tensile strength ISO 8339 0,5 N/mm 2 Elongation at break ISO 8339 250 % Modulus at 100 % elongation ISO 8339 0,37 N/mm² Hardness Shore A ISO 868 24 Movement capability ISO 11600 20 % Tear strength ISO 34, method C 3,0 N/mm

94. 91 retro-reflective warning marking retro-reflective warning marking Conforming to ECE 104 * Sticker spacing on the vehicle should be max 8cm

5. 2 s ilicone Joint dimensions for 310ml cartridge Joint Dimensions for 310 ml Cartridge Depth of joint (mm) 5 6 7 8 10 12 15 20 25 30 40 5 12.4 10.3 8.9 7.8 6.2 5.2 4.1 3.1 2.5 2.1 1.6 6 10.8 8.6 7.4 6.5 5.2 4.3 3.5 2.6 2.1 1.7 1.3 7 8.9 7.4 6.3 5.5 4.4 3.7 3.0 2.7 1.8 1.5 1.1 8 7.8 6.5 5.5 4.5 3.9 3.2 2.6 1.9 1.6 1.3 1.0 10 6.2 5.9 4.4 3.9 3.1 2.6 2.1 1.6 1.2 1.0 0.8 12 5.2 4.8 3.7 3.2 2.6 2.2 1.7 1.3 1.0 0.9 0.7 15 4.1 3.5 3.0 2.6 2.1 1.7 1.4 1.0 0.8 0.7 0.5 20 3.1 2.6 2.2 1.9 1.6 1.3 1.0 0.8 0.6 0.5 0.4 Width of joint (mm) The highlighted boxes indicate optimum joint dimensions for expansion joints. Joint dimensions Approximate number of tubes required per 100 metres for a given joint size mm 100 200 300 400 500 5 x 5 8 17 25 33 41 6 x 6 12 24 35 47 59 8 x 8 21 42 62 83 101 10 x 10 33 65 97 130 163 12 x 12 47 93 140 186 233 12 x 8 31 62 93 124 155 16 x 8 42 83 124 166 201 20 x 10 65 129 194 256 323 25 x 12 97 194 291 388 404 30 x 15 146 291 436 581 726 35 x 18 206 404 610 818 1017 40 x 20 258 517 776 1033 1287

7. 4 s ilicone product data Typical general characteristics Inspection Method Value Product data (uncured) Density at 25 °C ISO 1183-1 A 0,98 - 1,05 g/cm³ Consistency ISO 7390, profile U 20 non-sag Extrusion rate at 23 °C 450 ml/min Skin forming time at 23 °C / 50 % r.h. 20 min Product data (cured) After 4 weeks ́storage at 23 °C / 50 % rh Tensile strength ISO 8339 0,6 N/mm 2 Elongation at break ISO 8339 250 % Modulus at 100 % elongation ISO 8339 0,35 N/mm² Hardness Shore A ISO 868 20 Movement capability ISO 11600 25 % Tear strength ISO 34, method C 4,2 N/mm These figures are only intended as a guide and should not be used in preparing specifications

9. 6 s ilicone product data Typical general characteristics Inspection Method Value Product data (uncured) Density at 25 °C ISO 1183-1 A 0,98 - 1,05 g/cm³ Consistency ISO 7390, profile U 20 non-sag Extrusion rate at 23 °C 450 ml/min Skin forming time at 23 °C / 50 % r.h. 20 min Product data (cured) After 4 weeks ́storage at 23 °C / 50 % rh Tensile strength ISO 8339 0,6 N/mm 2 Elongation at break ISO 8339 250 % Modulus at 100 % elongation ISO 8339 0,35 N/mm² Hardness Shore A ISO 868 20 Movement capability ISO 11600 25 % Tear strength ISO 34, method C 4,2 N/mm These figures are only intended as a guide and should not be used in preparing specifications

11. 8 s ilicone product data Typical general characteristics Inspection Method Value Product data (uncured) Density at 25 °C ISO 1183-1 A 0,98 - 1,05 g/cm³ Consistency ISO 7390, profile U 20 non-sag Extrusion rate at 23 °C 500 ml/min Skin forming time at 23 °C / 50 % r.h. 20 min Product data (cured) After 4 weeks ́storage at 23 °C / 50 % rh Tensile strength ISO 8339 0,7 N/mm 2 Elongation at break ISO 8339 250 % Modulus at 100 % elongation ISO 8339 0,38 N/mm² Hardness Shore A ISO 868 18 Movement capability ISO 11600 25 % Tear strength ISO 34, method C 4,5 N/mm These figures are only intended as a guide and should not be used in preparing specifications

65. 62 e poxy resin a dhesive replast easy Complete system for easy and professional repairs of plastic parts. *Note Due in part to the coatings and release agents used when manufacturing plastics, in isolated cases there may be adhesion problems. Not suitable for the plastics PE(polyethylene) and PP (polypropylene)and PTFE (polytetra - fluoroethylene).If necessary, check material compatibility in an inconspicuous place. !

29. 26 panel adhesive mirror adhesive Art. No. 1890.600 Pack/Qty.: 1 Application The Mirror Adhesive is a high viscosity paste, gun grade adhesive, which is suitable for bounding mirrors up to a thickness of 4mm on all building surfaces like concrete, wood, paintwork, metal, glass, ceramic tiles, etc. Working methods For bonding mirrors with thickness above 2mm, applicate the adhesive with a notched trowel on the wall as well as on the backside of the mirror. Press the mirror in the adhesive. For bonding mirrors with a thickness up to 2mm, applicate a ring of the adhesive with the contour of the mirror. The ring has to be about 3mm. Press well. Correction of a few millimetres max. are possible within 10 minutes by sliding. Shelf life At least 6 months (between +5°C and +25°C) in closed cartridges.

44. 41 p olyurethane foam technical data The data shown can only represent a general guideline. Depending upon particular application circumstances and techniques beyond the control of the manufacturer, these guidelines cannot entitle to any claim. In any case we recommend sufficient pre-testing. A guarantee can only be given for high quality of our products. Determined at +20°C 60% p.h. and on well pre-moistened surface, 1 K-PU Foam upside down can be BE-B3 Contents 500 ml: approx. 22 litres Raw density (foamed into groove): approx. 25kg/m Cellular foam: medium-fine. Tack free (depending upon pre-reaction inside can): approx. 10 min. Cuttable (20 mm bead): approx. 24 min. Processing temperature (can & surface) Minimum: approx. +5°C Maximum: approx. +25°C Optimum: +15°C to +22°C Tensile strength (DIN 53455): 18 N/cm Elongation at tear (DIN 53455): 30% Shear strength: 8 N/cm Bending strength: 20 N/cm Compressive strain at 10% stress (DIN 53 421): 5 N/cm Water absorption (DIN 53428): 0.3 vol% Thermal conductivity (DIN 52612): 0.04 W/mK Expansion: approx. 15% Temperature resistance of cured foam bead Long term: +40°C to +100°C Short term: +40°C to +130°C. Shelf life: 9 months Store unopened, cool and dry environment, storage at higher temperatures might reduce shelf life considerably. The right to change physical properties as the result of technical progress is reserved. Important: During application of products with environmentally safe propellant, take care not to apply near naked flames or any incandescent material. Take extra caution around electrical equipment. Use ONLY in well ventilated areas - NO SMOKING. Vapours gathering in insufficiently ventilated areas might cause flammable and noxious concentration.

30. 27 fire cement Single component sealing compound which contains no solvents and possesses extremely high heat resistance, high strength and very good adhesion to metal surfaces. Application Fire Cement 1000 is suitable for use in heating equipment especially for sealing boilers, furnaces, stoves, chimneys, burner chamber linings, flue gas pipes and a very wide range of equipment and apparatus in the high temperature range up to 1000°C. Can also be used instead of sealing cord in the doors of boiler systems after annual service and / or cleaning. Application The sealing surfaces must be free from dust, grease, oil and loose rust and must be polished. Application temperature +5°C to +30°C. Drying time approx. 2 days. Sealant can only withstand heat when fully cured. Protect from persistent moisture. fire cement Specification Raw material base: Water glass cement with mineral fillers. Shelf life: 9 months at max. +30°C in sealed cartridge. If the cartridge is opened and sealed again, it should be used within 8 weeks. Specific weight: 221 g/cm≥. Shrinkage: Minimal. Expansion: None present - the dried cement has practically no elasticity. Consistency: Paste. Temperature resistance: +5°C to 1000°C (constant). Processing temperature: +5°C to 30°C. Colour: Grey. Odour: Neutral. Curing time: Approx. 2 days - protect from moisture during this period (dries in air). Increasing the temperature gradually can reduce the drying time. Resistant to: Greases, oils, domestic cleaning agents, flue gases and their condensations, dif - ficult to dissolve in water. Processing instructions: Base materials must be clean, dry and free from dust and grease. Container Contents ml Art No.: Pack/Qty. Cartridge 310 893 290 0 1

58. 55 s uper g lue profile ru BB er glue For adhesive bonding of rubber profiles on • untreated, primed or painted metal. Temperature resistance up to approx. • +100°C. Contents in ml Art. No. P. Qty. 180 0890 100 015 12

80. 77 a dhesive tapes m ounting instructions for adhesive mirror tape In case of mirror adhesion, make surethat the tape strips are applied only vertically and in several strips to reduce shearing and tractive forces and to distribute these forces across the entire adhesive surface. The listed lengths of adhesive tape should be distributed across the four corner points. q uantity of adhesive tape to use With this information we want to advise you to the best ofour knowledge based on our tests and experience. However, we can assume no liability for the application results in individual cases due to the large number of applications and to the fact that storage and application conditions are beyond our influence. This also applies to the use of the non-binding technical and commercial Customer Servicewe provide. We always recommend that you conduct your own tests. We guarantee the consistent quality of our products. We reserve the right to make technical changes and carry out further devel - opment. Adhesive Tape Mirror Surface 3mm 4mm 5mm 6mm 19mm 25mm 100cm 2 3cm 2cm 4cm 3cm 5cm 4cm 6cm 5cm 19mm 25mm 200cm 2 5cm 4cm 7cm 5cm 9cm 7cm 10cm 8cm 19mm 25mm 500cm 2 13cm 10cm 17cm 13cm 20cm 16cm 25cm 20cm 19mm 25mm 1000cm 2 25cm 20cm 40cm 30cm 45cm 35cm 50cm 40cm 19mm 25mm 2000cm 2 50cm 40cm 70cm 50cm 85cm 65cm 100cm 80cm 19mm 25mm 5000cm 2 125cm 100cm 175cm 120cm 225cm 170cm 250cm 200cm 19mm 25mm 10000cm 2 250cm 200cm 335cm 260cm 450cm 325cm 500cm 325cm

67. 64 e poxy resin a dhesive adhesive removal spray Easily removes hardened melt adhesive from the painted sur - face. Use a plastic wedge to gently lift the melt adhesive in one place. Spray the adhesive remover pre - cisely into the gap of the hardened melt adhesive and allow it to take effect for a short time. The plastic remover creeps into cavities and detaches the adhesive residues from the surface. The adhesive residue is removed in seconds from the surface in one piece. This eliminates the time- consuming removal procedure using a hairdryer, spatula and cleaning agent. Note: Check rubber and plastics for material compat - ibility. Areas of use: Special product for removing adhesives from the inside and outside of vehicles, caravans, mobile homes. For technical and leisure use Contents in mL Art. No. P. Qty 150 0893 141 1

42. 39 p olyurethane foam Art. No: 891.152 Pack/Qty: 1 High quality, Teflon coated gun. • Ideal for a controlled, accurate application. Always clean gun thoroughly • before storing. Features Valve spring: matched to the 1. output pressure of Würth PU foam. Valve ball: pure Teflon ball 2. ensures long service life. Teflon coated: Ensures the easy 3. cleaning of residues from the gun body. Triple Teflon seal: provides an 4. excellent leak proof seal between gun housing and nozzle. Teflon coated needle: fewer PU 5. residues = longer service life. Note: Guns should be cleaned through after every can of foam using PU cleaner Art. No.892.160. Uncured foam should also be cleaned from the outside of the gun body. 1 3 2 4 5 foam application gun

35. 32 pu sealer technical data Chemical basis 1-component polyurethane Density (DIN 53479) (before hardening) approx. 1.25 kg/l Application temperature +5°C to +35°C Skin formation time* 45-60 min. Hardening speed* 3 mm/24 h (moisture-hardening) Volume change (DIN 52451) approx. –5% Shore A hardness (DIN 53505) approx. 40 Tensile strength (DIN 53504) 1.8 N/mm 2 Elongation at tear (DIN 53504) approx. 500% Resistance to further tearing (DIN 53515) approx. 6 N/mm Elongation, compression during use 10% Volume resistivity (DIN 53482) approx. 1010Ωcm Glass transition temperature (DIN 53445) approx. –45°C Thermal stability –40°C to +90°CBriefly8 h at +120°C Resistant to Water, seawater and limy water, public waste water, weak acids and alkaline solutions. Briefly resistant to Fuels, mineral oils, vegetable and animal fats and oils. Shelf life 12 months (+10°C to +25°C) * measured at 23°C / 50 % rel. humidity Application: The application surfaces must be clean, dry, dust and grease-free (see Bond+Seal surface optimization). Mate - rial not hardened can be removed with B+S Remover, Art. No. 0890 100 63, while hardened material can only be removed mechanically. Note: Do not bring into contact with alkydresin paint systems. Not suitable forglass groove sealing in areas in whichUV back reflection can occur. Direct exposure to sunlight can lead to slight surface yellowing. Not suitable for PE, PP, PTFE, silicone rubber, expanded polystyrene and soft - ened plastics. Please remind to keep a minimum adhesive thickness of 3 mm for asecure bonding.

26. 23 panel adhesive pinkgrip What goes up won’t come down. Art. No. 8921.100.390 Pack/Qty.: 12 Amazing grabbing powers - grips instantly. • No need to pin under the workpiece. • No need for double-stick methods. • Can be used inside and out. • Adheres to most building substrates. • Firm favourite with tradesmen. • Comparison between the Pink Grip and any other grip

2. shops Würth Ireland Ltd, Monaclinoe Industrial Estate, Ballysimon Rd, Limerick. Tel: (061) 430200 Fax: (061) 412428 Fax Sales: (061) 415921 w Ü rth shops around ireland Cork Trade Unit Unit 3 Kinsale Road Commercial Centre Kinsale Road Cork Tel: +353 21 432 0260 Fax: +353 21 432 0261 Würth Ireland Ltd. Head Office, Moniclinoe Industrial Estate, Ballysimon Road, Limerick. Tel: +353 61 430200 Fax: +353 61 412428 www.wurth.ie Ballymount Trade Outlet, Dockrells Complex, Ballymount Road Upper, Ballymount, Dublin Tel: +353 1 429 8002 Fax: +353 1 429 8649 Sandyford Trade Outlet Unit E2, Sandyford Industrial Estate, Three Rock Road, Dublin 18. Tel: +353 01 207 4506 Fax: +353 01 207 4509 Finglas Trade Outlet Unit D9, North City Business Park, North Road, Dublin 11. Tel: +353 1 864 2429 Fax: +353 1 864 2632 Belfast Trade Outlet Unit 1 and 2, Dargan Court, Dargan Crescent, Duncrue Ind. Est., Belfast. BT39JP Tel: 02890 775 141 Fax: 02890 770 927 Go to our website www.wurth.ie

41. 38 p olyurethane foam 150 ml Art. No: 892.16 Pack/Qty: 1 For removing fresh PU foam spills from clothing or other • surfaces. 500 ml Art. No: 892.160 Pack/Qty: 1 For cleaning foam guns. Fits directly onto gun, to spray • through. Additional spray nozzle to remove fresh foam spills • from clothing or other surfaces Attention: Hardened PU foam can be removed using Foam Cleaner Art. No: 8921.155.150. pu cleaner

52. 49 w ood g lue Surface Preparation Surfaces to be bonded must be clean, dry and dust/grease free. When bonding plastic laminates/sheeting, it is recommended that substrates are conditioned for 48hrs before assembly at 20oC with a relative humidity of 45-55%. Air should be able to circulate freely around these components. ALWAYS READ SAFETY SECTION AND WEAR PROTECTIVE CLOTHING, GLOVES AND EYE/FACE PROTECTION BEFORE USE. Application Ensure hose is screwed into position on both gun and canister, taking care not to cross thread or damage the thread. Ensure lock on spray gun is en - gaged. Fully open the valve on the canister and direct the gun at the surface to be bonded. Before applying, ensure the gun is correctly adjusted and test spray on a practice piece. Adjust knob at rear of gun until an even fan of 5-9” of fine strands of adhe - sive is produced. If the adhesive is “wet” tighten knob until only fine strands appear. Fitting hose and gun to new canister: Close valve on canister completely. Hold gun trigger open, pointing away from person, until all pressure is released. Disconnect the hose at the valve and re-connect to a new canister. Open valve and check fittings for leaks. Permanent bonding (laminates etc) - Apply to both surfaces. Always apply to laminate first and spray one surface horizontally and one surface vertically. Hold the spray gun at 90` to, and at a distance of 12-14 inches from the substrate. Do not hold closer than 12 inches to avoid “wetting” the surface. Squeeze trigger and move gun parallel to the surface in a smooth motion paying particular attention to the edges. Apply an even coat ensuring 80- 100% coverage. Avoid localized spraying as this will allow the adhesive to puddle which in turn can cause unevenness and can “show” through the laminate or cause blistering. One coat is normally sufficient per side for non porous substrates. A second coat is recommended on porous substrates. Al - low the adhesive to tack up and protect from contamination (dust etc) whilst this happens. The adhesive is ready for bonding when the whole area is touch dry, i.e. does not transfer to the finger when touched. SMART TACK BULK TANK is normally ready for bonding within 3-5 minutes at 20`C/50% relative humidity and may be left open for up to 2 hours be - fore bonding. Ensure there are no wet patches of adhesive before bonding. At low temperatures, care must be taken to ensure that the temperature of the adhesive and of both surfaces to be bonded is higher than the ambient tem - perature. Cold materials have a strong tendency to attract moisture present in surrounding air, which can have disastrous effects on the bond strength. Temporary or light duty bonding (carpets, fabrics, polysty - rene sheet etc) - Apply as above but to the substrate surface only. Never apply direct to polystyrene. Always apply to the “other” surface. COVERAGE: 255-340m2 per 17kg can. Health & Safety Consult MSDS for full list of hazards. Storage Store in original unopened containers between 5 and 25 o C. Store as flam - mable liquid. Shelf Life Twelve months from date of manufacture in original unopened containers. The technical data contained herein is based on our present knowledge and experience and we cannot be held liable for any errors, inaccuracies, omis - sions or editorial failings that result from technological changes or research between the date of issue of this document and the date the product is acquired. Before using the product, the user should carry out any necessary tests in order to ensure that the product is suitable for the intended applica - tion. Moreover, all users should contact the seller or the manufacturer of the product for additional technical information concerning its use if they think that the information in their possession needs to be clarified in any way, whether for normal use or a specific application of our product. Our guar - antee applies within the context of the statutory regulations and provisions in force, current professional standards and in accordance with the stipulations set out in our general sales conditions. The information detailed in the pres - ent technical data sheet is given by way of indication and is not exhaustive. The same applies to any information provided verbally by telephone to any prospective or existing customer. application Specific Data Base Synthetic rubber/resin Solids 28 - 32% Viscosity Low Coverage 15-20m 2 Tack Life 3 mins to 2 hours Specific Gravity 0.90 - 0.99

72. 69 thread lock & pipe sealant flange sealant, green For sealing of flanges and sur - faces with a small gap of 0.3 mm max. Replacement for solid - seals. Particularly well suited for applications requiring good wet - ting, such as complicated cast - ings, narrow webs and smooth surfaces. ► Low strength. Your advantage: Easy disassembly. • Contents Art. No. P.Qty. 50 g 0893 573 050 1 250 g 0893 573 250 Physical Properties (in liquid state) Physical Properties (in cured state) Chemical description Dimethylacrylate Color Green Viscosity 25 °C Brookfield (RVT/RVT/HB) 40,000–60,000 mPas (spindle rpm: 6/2.5) 15,000– 25,000 mPas (spindle rpm: 6/20) Density 1.05 g/cm 3 Flash point > 100 °C Shelf life 1year at room temperature Hand-tight after 15–30 minutes Usable after 3–6 hours Final strength after 6–24 hours Initial breakaway torque 8–10 Nm (M10) Continuing torque 3–5 Nm (M10) Pressure shearing strength (DIN 54452) 4–6 N/mm 2 Tensile strength 2–4 Nmm 2 (ASTM-D-2095) Impact shearing strength 2–4 Nmm/mm 2 (ASTM-D-950) Operating temperature range –55°C to +150°C

31. 28 fire cement Pyrocryl intumescent sealant. White Art. No. 892.317.299 Pack/Qty.: 1 Description Fire rated emulsion acrylic sealant that swells when subject • to temperatures in excess of 125°C to block the passage of fire and smoke. Tested to BS 476 Part 20 and Part 22. • Flexible, excellent adhesion to most building substrates. • Applications Sealing, filling and pointing to fire rated partitions. • Sealing through gaps in firecheck walls. • Sealing construction joints in fire rated structures where • movement will not exceed + or -15%. Sealing around firecheck door frames. • fire retardent sealant

71. 68 thread lock & pipe sealant flange sealant, orange For sealing of flanges and surfaces with a gap of 0.5 mm max. Replacement for solid seals. ► Large gap filling capability. Your advantage: Completely fills rough surfaces. • Contents Art. No. P.Qty. 50 g 0893 574 050 1 250 g 0893 574 250 Physical Properties (in liquid state) Physical Properties (in cured state) Chemical description Dimethylacrylate Color Orange Viscosity 25 °C Brookfield (RVT/RVT/HB) 80,000–120,000 mPas (spindle rpm: 6/2.5) 30,000– 40,000 mPas (spindle rpm: 6/20) Density 1.05 g/cm 3 Flash point > 100 °C Shelf life 1year at room temperature Hand-tight after 10–20 minutes Usable after 3–6 hours Final strength after 6–24 hours Initial breakaway torque 17–22 Nm (M10) Continuing torque 13–17 Nm (M10) Pressure shearing strength (DIN 54452) 5–10 N/mm 2 Tensile strength 8–10 Nmm 2 (ASTM-D-2095) Impact shearing strength 5–10 Nmm/mm 2 (ASTM-D-950) Operating temperature range –55°C to +150°C

87. 84 gasket sealer s ilicone rtv Low volatile, high-temperature silicone adhesive and sealant Oxygen sensor safe - no risk of engine problems • resulting from damaged circuit boards or electronics components as can be the case with non-compatible compounds Ideal for making gaskets on all engines, sealing • windscreens, light housings, hose connections and for insulating wiring. Temperature resistant from -73 • ° C to +315 ° C. Resistant to all transmission fluid, anti-freeze, diesel • fuel, water, steam and lubricants. Conforms to GM 9985443 • Application; Clean sealing surface thoroughly. Depress nozzle to one side and apply a thin even bead to one surface. Allow 10 mins before final assembly. Remove excess RTV with a non-flammable cleaning fluid or once cured with a knife. Sealant is fully cured in 10-12 hours. After use leave a small amount of silicone protruding from nozzle and replace cap. This will cure and act as an easily removed plug when used next. Caution; Uncured sealant evolves acetic acid slowly during cure. Please follow safety and usage guidelines on container. Art. 890 910 2 - Red 890 910 3 - Black

19. 16 Bitumen mastic For filling joints with bitumen strips. Excellent adhesion on bitumen strips. • Your advantage: Seals roof sheeting and roofing paper very reliably. Good adhesion on damp surfaces. Your advantage: Use largely independent of weather conditions. Suitable for emergency repairs. Other advantages: Resistant to ageing and weathering. Suitable for elastic moulding. Applications: For sealing off roof sheeting and roofing paper. For filling in joints of roof passages, e.g. domed roof lights, ventilation ducts, antennas or chimneys, as well as edge connections. Suitable for emergency repairs. Typical application surfaces: without primer: bitumen, zinc plating, copper plating, stainless steel, concrete, clinker. By very porous surface use primer, Art. No. 08972 875. Technical Data B itumen sealant Raw material base Bitumen Primer Not required. Max. absorption of contin. movement 10% Skin formation time Approx. 30 min at +23°C and 50% rel. humidity Curing speed Approx. 1mm after 24 hrs. at +23°C and 50% rel. humidity Thermal stability –35°C to +110°C Application temperature +5°C to +35°C Can be painted over No Compatibility with paint No Contains fungicide No Shore A hardness – Density Approx. 1.38 g/m 3 Elongation at rupture with 2 mm film – Shelf life 12 months Container Contents ml Art. No. P. Qty. Cartridge 310 0890 103 12

27. 24 panel adhesive gripfill™ Solvent borne rubber resin adhesive. • High strength, gap filling. • Bonds a large variety of materials. • Description GRIPFILL™ is a solvent-borne, filled rubber resin adhesive, developed to bond virtually any rigid materials together, regardless of the evenness of the surfaces. Uses GRIPFILL™ is a high strength, one part, gap-filling adhesive specially formulated to bond a large variety of materials, such as plywood, blockwood, chipboard, hardboard, laminated plastics, uPVC (excluding foamed PVC), rigid insulation materials (excluding expanded polystyrene), metal sheeting (including aluminium, steel, galvanised iron, tin plate and non-ferrous metals) to themselves or to brick, stone and breeze block, sand/cement screeds, concrete, plaster, plasterboard and insulation boards. If further details of a particular application are requires, please contact our Technical Department. GRIPFILL™ is suitable for bonding aluminium and uPVC stair nosings, carpet-edging strips, carpet grippers, building boards, timber battens, etc to stairs, floorboards and walls. GRIPFILL™ can also be used successfully for bonding wall signs, window frames, sink units, fitted furniture (including light fittings) to a variety of surfaces; in the building of home extensions, caravans and cars. * Although GRIPFILL™will bond mirrors, care should be taken to ensure no reaction takes place with the coating, as this may occasionally occur. Where GRIPFILL™ is used externally, it must be protected from driving rain, ponding water or permanently wet situations. This can be achieved by use of a silicone sealant. Application Fix the cartridge into the extruder. Cut the nozzle to the desired width and angle and push a nail through the nozzle to break the seal at the base. a) Star Nosing, Window Frames etc. Apply a continuous bead (usually 6 mm in dia.) to the surface being bonded. Position on the substrate, if possible by sliding into place and apply pressure overall. If the object is to be applied to a vertical surface, temporary mechanical support (e.g. panel pins, masonry nails etc) may be required. Allow to dry overnight prior to any further operation e.g. fixing boards to battens, etc. b) Wall Panels For most work, GRIPFILL™ should be applied as a bead approximately 6 mm diameter to rear of the panel. Extrude a continuous bead around the panel approximately 25 mm from the edge. Additional beads should then be applied across the panel at 600 mm centres (450 mm for heavy panels) Immediately present the panel to the wall slightly above its required position and applying pressure slide it into place in order to break any surface skin. Press firmly to ensure maximum overall contact, using a soft mallet if necessary. Continue as above with further panels making sure they are flush with each other. Any adjustment must be made within 5 minutes of placing. Alternatively, GRIPFILL™ may be applied in the form of blobs approximately 10 - 12 mm in diameter at 300 mm centres, in rows either 450 mm or 600 mm across the board (depending upon the weight as above). The blob application is not recommended when bonding plastic. c) Impervious Materials Where two impervious materials are to be bonded, apply GRIPFILL™ as above, press firmly together and break the bond by pulling away immediately ensuring good transfer has occurred. Wait for approximately 5 minutes and rebond the two materials. Description Contents ml Art No.: Pack/ Qty. Cartridge 350 01892 10 350 12 Preparation Surfaces to be bonded must be clean, structurally sound, dry and free from dust and loose material. Porous surfaces, such as plaster and fibre cement board, should first be primed with PVA (diluted 1:6 with clean water) and allowed to dry thoroughly before GRIPFILL™ is applied. Building panels should be cut to shape beforehand.

33. 30 pu sealer B ond and seal Application Requirement Elastic with great elasticity Elastic with great elasticity UV and weather- resistant Food process- ing sector (cer-tifi - cate/NSF) Coatable, paint - able, with wait time Coatable, paintable, immediate Dynamic/ mechani - cal high loads OK Quick final strength Seam sealing/Joints (e.g. overlapping chassis seams, container seals, step-by-step welding seams, housing seals, expansion joints, gap seals) B + s B + s B + s B + s fast B + s fast B + s fast B + s all in 1 B + s all in 1 B + s all in 1 Restoration of the original structure B + s all in 1 B + s all in 1 B + s all in 1 Visible joints (e.g. connection joints) B + s B + s B + s B + s fast B + s fast B + s fast B + s power B + s power B + s power B + s power B + s power B + s power Area adhesion (e.g. bumper plates, bed plates, corrugated sheet metal and steps of carrier plates, corner and edge protection plates) B + s B + s B + s B + s B + s fast B + s fast B + s fast B + s power B + s power B + s power B + s power B + s power B + s power Seam adhesion/ Point adhesion (e.g. sheet metal overlaps, angle profiles, truck side panels, mounts, frame adhesions, sign and board mounting) B + s power B + s power B + s power B + s power B + s power Adhesion of tuning parts (e.g. spoilers) Observe the manu - facturer’s instructions! B + s B + s B + s power B + s power B + s power B + s power Applications/Requirements/Products Note: First select the most important requirement for your application. Then locate the suitable product on the “Application” line.

17. 14 s ilicone s ilicone c olour Technical data Max. absorption of continuous movement 25 % of joint width Skin-forming time approx. 10 – 15 min; at 23°C / 50 % rel. humidity Curing speed approx. 2 mm / 24 h; at 23°C / 50 % rel. humidity Temperature stability – 40°C to +120°C Working temperature + 5°C to + 40°C Can be painted over No Compatibility with paint Yes Contains fungicide Yes Shore-A hardness approx. 20 Density 1.03 g/cm³ Elongation at failure with 2 mm fi lm approx. 600 % Shelf life (with cool, frost-free storage) 9 months With this information, we want to advise you to the best of our knowledge based on our tests and experience. Preliminary testing required! For further information, see the Technical Data Sheet. Additional article RAL Color Card Art. No. 0705 800 010 Cartridge Gun Art. No. 0891 ff. Silicone Primer Art. No. 0892 170 Joint Smoother Art. No. 0891 18 ff. Sealant Smoothing Agent Art. No. 0893 3/003PE Back fi ll Material Art. No. 0875 ff. Cartridge Knife Art. No. 0715 66 09 ! Your procedure for obtaining individually produced special silicone colors: Entry of article number 0892 580 0 1. Selection of the desired RAL color based on the RAL color card (Art. No. 0705 800 010) and specification of 2. the RAL number. Color specification in the system is always carried out with the RAL No. in the order-related text. Please note:Neon and metallic colors cannot be produced for technical reasons (RAL No.: 1026, 2005, 2007, 3024, 3026, 9006 and 9007). Specification of the quantity. This must always be a multiple of the packing unit 12. 3. Order is sent and conveyed to Production. 4. Production of the Silicone Color in the desired RAL color for the individual customer. 5. Note: Silicone Color is a special product for individual customers. For production reasons, minor fluctuations in the color can occur. This is not a product defect. No exchange possible. Carry out color matching with existing material prior to application. After 20 working days you receive your Silicone Color produced in your individual color. 6.

73. 70 thread lock & pipe sealant high - strength B earing lock For high-strength fastening of bushings, sleeves, gearwheels, pins, shaft and hub connections and bearings subjected to heavy loads. Reliable hardening at low temperatures down • to 0°C. Also a reliable helper in winter! Can also be used on slightly oily surfaces.You • save time-consuming degreasing of bearings Maximum gap fi lling capacity of 0.15 mm. • Even major deviations can be corrected at low cost! Prevents fi ctional corrosion. Prevents bearings • from seizing. Contents Art. No. P.Qty. 25 g 0893 603 025 1 50 g 0893 603 050 250 g 0893 603 250 Physical Properties (in liquid state) Physical Properties (when hardened) Chemical characterization Methacrylic ester Color Green Viscosity (spindle 4/20 rpm) 25°C Brook fi eld RVT 100 – 150 mPas Density 1.07 g/cm 3 Max. thread diameter M 12 Max. gap fi lling capacity 0.15 mm Flash point > 90 °C Shelf life 1 year at room temperature Setting to the touch after 5 – 0 minutes Usable after 30 – 40 minutes Final setting after 3 – 6 hours Break-loose torque Eliminated Just-move torque Eliminated Compression shear strength (DIN 54452) 18 – 26 N/mm 2 Temperature range –55°C bis +150°C

39. 36 p olyurethane foam One component moisture curing multi- purpose foam suitable for use in the construction industry. Art. No: 892.152.1 Contents: 750 ml Pack/Qty.: 1 Resistant to extremes of temperature. • Economical in use. • Once cured, will not rot. • Offers good insulating properties. • Foam yield - approx. 40 litres. • A single component, polyurethane based, gun applied expanding foam with many uses in the building and construction industry i.e: gap filling around window frames, filling voids around steel work, etc. The foam offers excellent resistance to: age, heat, cold, most chemicals, rot and pests. Note: When cured the foam is not UV stable. When applying the foam surfaces must be dampened in order to enable the foam to curefully and obtain maximum adhesion. Technical Data Base: Humidity-hardening polyurethane polymer. Ideal working conditions: 15 to 25°C, 60% rel. Humidity, base material well moistened. PU Content: 672 gms = 45 litres yield (RG 15), 50 litres when foamed. Gross density: Approx. 15 - 25 mg/m≥ Cellular structure: Medium-fine, predominantly closed. Touch-dry*: After 7 min. Cuttable*: After 20 min. Support removable: After 120 min. Workable: At >5°C. Tensile strength DIN 53 455 18 N/cm≤ Rupture strain DIN 53 455: 30%. Shear strength DIN 53 422: 8 N/cm≤ Compression strain at 10% compression deformation DIN 53 421: 5 N/cm≤ Water absorption DIN 53 428: 0.3% by volume Thermal conductivity: 0.04 W/mK After foaming: Approx. 150%. Temperature resistance: From -40 to +90°C, for brief periods -40 to +130°C. Resistant to: Ageing, heat, cold, many chemicals, rotting and vermin. UV resistant: No. Shelf life: Up to 9 months at temperatures below +20°C. * Under ideal working conditions. fixing foam

50. 47 w ood g lue Colour Article No.: Pack Size Qty White 98921 700 1 3Kg 1 White 98921 900 1 25Kg Bag 1 Art. No. 892.100.175 Pack/Qty.: 1 Solvent free application. • Outstanding adhesion to many substrates. • Strong rigid bonds. • Resistance to high and low temperature. • Resistance to moisture. • Uses Polyurethane Glue may be used for bonding all types of timber, plastic foams and other insulating materials to a wide variety of both flexible and rigid facing materials in the manufacture of structural sandwich panels and insulating building boards and laminates. Pressing Once the adhesive has been applied and the panel assembled, sufficient even pressure must be applied to keep the components in intimate contact during the cure cycle. The actual pressure required depends on the nature of such adherents but is generally in the range of 4-10 psi (0.3-0.7 kg/sq.cm). Such pressures may be obtained by using a platen press, air-bag or vacuum press. polyurethane glue Application a pplication gun for polyurethane glue Art. No. 891.152.500 Pack/Qty.: 1

85. 82 p . t . f . e t ape ptfe thread sealing hemp The universal thread sealant made of100% pure, multi-fiber PTFE for sealingmetal or plastic thread connections. Application Used to seal pipe threads up to 6”for: Also highly suitable for compressed-air, hydraulic, pneumatic and a variety of other types of applica - tions. Advantages 100% PTFE • Tried-and-tested material for sealing threads. Resistant to almost all known chemicals and micro - biological processes. Multi-fiber • Inserts well into the thread. High tensile strength and highly tear-resistant. DVGW approval • Safety-tested in gas, drinking-water and hot-water applications. Can be adjusted/turned back up to 45°. Permanently elastic • Does not harden, does not become brittle, does not rot, lasts indefinitely. Silicone-free • Material 100% pure PTFE (polytetrafluor ethyl - ene), silicone-free Temperature resistance –200°C to +260°C DVGW tested, ARp class For gas, drinking water and hot water according to DVGW approval NV-5142 BS0140 Resistance to chemicals, liquids, oils, solvents, gases and acids very good Resistance to mold, fungus and bac - teria very good Technical data Spool Length Art. No. P.Qty. 150 m 0985 030 150 1

40. 37 p olyurethane foam BS 476 Part 20. Art. No: 892.152.51 Contents: 750ml Pack/Qty.: 1 Tested as a fire seal in horizontal and vertical joints to BS 476 Part • 20 for up to 4 hours. Enhanced performance can be achieved by over capping with • intumescent sealant. Single component, easy to apply. • Also meets Class B1 of DIN 4102 Part 1. • Technical Data Warrington Fire Research testing of Würth Fire Rated Gun Grade Foam. The floor construction comprised 250 mm thick aerated concrete. The wall construction comprised 220 mm thick autoclaved blockwork. Colour: Pink UV resistance: The cured foam is NOT resistant to UV light and should be capped/covered after application. Biological resistance: Resistant to vermin, insects and attack by fungus. Closed cell structure: >60% Tack free time: 10-15 mins (at 23ºC, 55% RH) Cuttable time: 30-45 mins (at 23ºC, 55% RH). Once fully cured Fire Rated Gun Foam can only be removed mechanically, ie by scraping or cutting. Excesscured material may be trimmed usinga sharp knife or sanded down. Uncured foam should be removed/ cleaned using PU Cleaner Art. No. 892.160 Application temperature: +5ºC to +25ºC Service temperature: -30ºC to +90ºC (Short period to 120ºC) Yield per can: A 750ml can will yield approx. 35 litres of foam. The actual amount will depend on the ambient temperature and humidity conditions. Dampening surfaces to which the foam is applied will assist curing and maximise the yield obtained. width mm Depth mm 10 20 30 40 50 10 300 150 100 75 60 20 150 75 50 37 30 30 100 50 32 25 20 40 75 37 25 19 14 50 60 30 20 15 12 Estimating Requirements: The table below gives an estimate of the linear metres each can should yield for a given joint size. The actual amount will depend on the ambient temperature and humidity conditions. Gap width (mm) Seal depth (mm) Orientation Description Integrity (mins) Insulation (mins) 45 220 vertical PU foam/min - eral fibre core 240 240 30 220 vertical PU foam/min - eral fibre core 240 240 15 220 vertical PU foam 240 240 45 220 horizontal PU foam/min - eral fibre core 240 240 15 220 horizontal PU foam 206 206 fire rate gun foam

56. 53 s uper g lue A high tack medium viscosity one part neoprene contact adhesive. Long open time. • Easy application. • Low soak - to avoid glue line starvation. • Uses This highly versatile adhesive will bond a large variety of materials including: plastic laminate, aluminium, sheet lead, hardboard, wood veneers etc. to a variety of core materials. Application Preparation: • For maximum bond integrity: Precondition adhesive and materials to be bonded at 15°C - 20°C. Surfaces should be free of grease and dust. Stir vigorously before use. Spreading: • By hand or roller at 4.1 2 - 6.2 2 / litre to both surfaces to be bonded. Ensure total area is covered. Drying time: • 10 - 15 minutes. Open time: • Up to 5 hours. Drying time and open time are both dependant on adhesive coverage and ambient conditions. Adequate drying time must be allowed to avoid solvent entrapment. Assembly: • Carefully align materials before contact. Press surfaces together at maximum pressure consistent with the materials being bonded. Use cold press, hand rollers, block and hammer etc. Maximum adhesive performance is dependant on sufficient pressure being applied. Description Contents ltr Art No.: Pack/ Qty. Canister 5 8901.100.099 1 contact adhesive

90. 87 chemical anchor chemical anchor system Polyester Styrene Free Enables the bonding of awkward fixings and problematic • materials. The ployester resin has ease of application and high tensile • strength when set. Applications; Hollow materials: Remedial wall tiles, wall plates, brackets and fabricated stairways. Solid materials: Railings/balustrades, reinforcing rods, retaining masonary facades using threaded rod. Services: For fixing pumps, fans, vibration proof fixing of motors, radiators, air conditioning units etc. Cure times: at 5 0 C - 50 minutes at 15 0 C: 35 minutes at 25 0 C: 30 minutes Art. 9031 380 500.380ml chemical anchor system Epoxy Acrylate Styrene Free As above but approved for under water use • Cure time should be doubled when used in wet holes. • Art. 9031 380 550.380ml Additional articles ml gun 9031 10 380 Static Mixer Nozzle 9031 380 991 !

86. 83 p . t . f . e tape ptfe thread sealing tape Application: Used to seal thread connections. • Advantages: DVGW-tested (thickness: 0.1mm) pursuant to • DIN EN 751/3 (97) and DIN 30660 (99). Resistant to all aggressive media. • Thermal stability* –240°C to +240°C. • Pressure resistance* up to 25 bar. • Does not stick or swell. Therefore prevents • seizing of the thread. Alignment of the thread connection, which • includes limited turn-back, is permissible. *Since the temperature and pressure are dependent on one anoth - er, it is not permissible to allow both to be pushed to maximum levels simultaneously. In addition, the specifications depend on the respective medium. For this reason, these specifications can only serve as a guideline due to the variety of application options (see also DVGW approval). Designation Width in mm Length in m Thickn. in mm Surface based mass g/m2 DVGW tested For Art No.: P.Qty FRp PTFE Thread Sealing Tape 12 12 0.1 60 x Fine thread (DN≤10) 0985 030160 10 GRp PTFE Thread Sealing Tape 12 12 0.1 100 x Coarse thread (10<DN≤50 0985 030161 PTFE Thread Sealing Tape 12 12 0.08 25 - - 0985 030165

47. 44 w ood g lue Universal glue, PVAc base, very fast setting. Characteristics Very fast setting. • Very short open time. • Fulfils requirements group D1 and D2 in accordance to EN 204. • Areas of application Gluing of veneers. • Gluing large areas of laminate. • Gluing carcasses / gluing for assembly purposes. • Technical data Base: Polyvinyl acetate Colour: White, dries transparent. Density: Approximately 1.1g/cm≥ Solid content: 54% pH value: Approx. 5 Viscosity: 15,00 mPas Method of application: On one side Application devices: Brush, spatula, roller, spray bottle Quantity applied: 100 to 160 g/m≤ Open time: 3 to 10 minutes Contact pressure: 0.2 N/mm≤ Minimum pressure time: At 20°C: 3 mins. / at 50°C: 2 mins. / at 70°C: 1 min. Processing temperature: Minimum 15°C Duration of storage: 1 year in closed original containers, protect from frost. Cleaning: Wash machinery and equipment with cold or warm water immediately afteruse. Note: Contact with ferrous metals i.e. steel or iron can cause the glue to turn blue or black. Avoid contact with steel clamps etc. Description Contents Art No.: Pack/ Qty. Bottle 500g 892.100.12 1 25 kilo 892.100.13 quick-setting glue

75. 72 thread lock & pipe sealant high- strength screw fixer Screw fi xer and sealant – diff cult to detach. For locking, fi xing and sealing screws, stud bolts, nuts, threaded inserts and screw plugs that will not normally have to be removed again. Particularly suitable for screw connections • subjected to heavy stresses No additional securing parts required. Disassembly only possible after heating to • 300°C ! Under normal conditions, can only be detached using a special tool and/or under the in fl uence of temperature Excellent resistance to media and heat • Universal products with a wide range of potential applications Prevents loosening due to e.g. vibrations and • impact stresses No unwanted locking problems, e.g. as in the case of mechanical screw locks • NSF-tested in accordance with NSF/ANSI 61 Contents Art. No. P.Qty. 25 g 0893 270 025 1 50 g 0893 270 050 250 g 0893 270 250 Physical Properties (when liquid) Physical Properties (when hardened) Setting to the touch after 10 – 20 minutes Usable after 1–3 hours Final setting after 5–10 hours Break-loose torque > 30 Nm (M10) Just-move torque > 45 Nm (M10) Compression shear strength (DIN 54452) 12 - 15 N/mm 2 Temperature range –55°C to +150°C Chemical characterization Dimethacrylic ester Color green/ fl uorescent Viscosity 25°C Brook fi eld RVT) 400–600 mPas (spindle rpm: 2/20) Density 1.11 g/cm 3 Max. thread diameter M 20 Max. gap fi lling capacity 0.15 mm Flash point > 100 ̃ Shelf life 1 year at room temperature

69. 66 thread lock & pipe sealant hydraulic seal Used to seal pneumatic and hydraulic screw connections under high loads. Up to the burst pressure of the pipe/hose with screw connections. ► Can also be used on lightly-oiled surfaces. Your advantage: You do not need to waste time removing • grease from fittings. ► Excellent resistance to all hydraulic fluids and fuels. Your advantage: Very safe, as damage caused by disintegra - • tion is prevented. ► Quick hardening, even at low temperatures: touchable in 40 minutes, usable after 2 to 3 hours. Your advantage: Shorter vehicle downtimes. • Contents Art. No. P.Qty. 50 g 0893 545 050 1 250 g 0893 545 250 Physical properties (when liquid) Chemical characterization methacrylic ester Color violet Viscosity 25°C Brookfield (RVT) 1,500 – 2,000 mPas (spindle r.p.m.: 5/2,5) Density 1.20 g/cm 3 Max. thread diameter R 3/4'' Max. gap filling capacity 0.15 mm Flash point > 100 °C Shelf life 1 year at room temperature Physical properties (when hardened) Setting to the touch after 30 – 40 minutes Usable after 2 – 3 hours Final setting after 12 – 24 hours Break-loose torque 2 – 3 Nm (M10) Just-move torque 1 – 2 Nm (M10) Compression/shear strength 1 – 3 N/mm 2 Temperature range –55°C to +150°C

70. 67 thread lock & pipe sealant motor sealant Replacement for solid engine seals on pressure chambers as well as screw connections. ► High temperature resistance. Your advantage: Seals reliably up to temperatures of +280°C. • ► Pressure resistant up to 700 bar. Your advantage: Also suitable for high pressure lines and pressure chambers. • ► Excellent adhesion. Your advantage: Seals glass, ceramic and metal surfaces permanently and • securely. Resistance List The engine sealing compoundMOTORSEALANT has good resistan - ceto the following media: Engine oil, transmission oil, hydraulic oil (mineral, synthetic), diesel fuel, heating oil, coolant, brake fluid, waste water, alkaline lye, formic acid, alcohols (methyl, ethyl, etc.), ethyl acetate, acetone, chlorinated solvents, phosphoric acid (10%). Gases: acetylene, carbon dioxide, propane, sulfur dioxide, hydro - gen.Due to space limitations this list is incomplete and restricted to the most important media. A complete list is available upon request. Note: The above information is intended as a recommendation only, based on our experience. As a matter of principle, we recommend that you carry out your own tests. Usage Notes: The product is thermosetting. From approx. +60°C it hardens into a self-contained seal. Apply a very thin coat of pruduct to one side of a clean and dry surface and let aerate approx. 20 minutes before joining the two pieces. In case of later repair, the surfaces can be separated relatively easy. Caution: Not suitable as cylinder head gasket Contents Art. No. P.Qty. 100 g 0893 260 100 1 Components 1 Base Resin Specific weight at +20°C 1.08 Film formation, potlife 5–7 minutes Thermal behavior –50 °C to +280 °C Pressure tested up to approx. 690 bar Viscosity in mPas approx. 5,000–13,200 pH value approx. 7 Shelf life 1 year Total deformation 25% Technical Values

61. 58 w indscreen a dhesive g lass sealant - remova B le Sealant for external sealing of vehicle windows. Areas of application: Glass Sealant Removable is a black, spreadable sealant for sealing windshields, rear and side windows, and can also be used for comparable sealing applications. Application: Apply between glass and rubber profile and between rubber profile and body flange. Excess material can be dabbed off with the sealant itself or body sealing tape after a short flash-off time. Highly compatible with most materials • Your advantage: Does not attack chrome, paint or rubber Temperature-resistant from –20°C to +80°C • Resistant to water and caustic solutions • No embrittling • Remains soft-elastic and slightly adhesive on the surface • special adhesive Description Contents ml Art No.: Pack/ Qty. Glass Sealant 310ml 0890 100 043 1/12 For easy gluing of glass and metal with and to each other. Areas of application: Inside rear-view mirrors on vehicles, metal clamping bolts, hinges on hinged side windows etc. Application: Thoroughly clean surface to be bonded with acetone cleaner 1. and dry. Then apply activator to base surface. Apply adhesive to metal surface 2. Press metal surface onto glass surface for approx. 20 sec. 3. Adhesive bond can already be loaded 50 % after 15–20 min Impact and vibration-resistant adhesive bonding • . Your advantage: Lasting permanent connection between glass and metal Outstanding resistance to chemicals. • Your advantage: Highly resistant to diluted acids and alkaline solutions, water and alcohol ! Description Contents ml Art No.: Pack/ Qty. Special Adhesive Plastic bag 1g, activator ampoule 0.5ml 0893 40 1 Technical Data: Colour after curing Transparent Temperature resistance -55 0 C to +120 0 C Final Strength After approx. 12hr* * 23 0 C / 50% rel. humidity

10. 7 s ilicone silicone acetate (standard grade) Art. 00892 317* 1 / 2 / 3 / 5 / 6 / 9 / 10 / 20 Product description One-component, acid-curing, silicone sealant for general-purpose sealing. Silicone Acetate - std cures at room temperature under the action of atmospheric mois - ture to give a permanently flexible silicone rubber. Special features non-sag • ready gunnability at low (+5°C) and high (+40°C) • temperatures flexible at low (-40°C) and high temperatures • (+100°C) rapid crosslinking: quickly becomes tack-free • available in a wide range of colors • excellent tooling properties for professional use • Application Sealing of connecting and expansion joints in indoor • applications and for bonding and mending tasks. Restrictions on use Silicone Acetate - std should not be used on substrates such as marble, concrete, fibrous cement and mortar, as the product releases acetic acid during vulcanization. Silicone Acetate - std should not be used in contact with metals such as lead, copper, brass or zinc due to corro - sion. Silicone Acetate - std may be discolored in contact with some organic elastomers, e.g. EPDM, APTK and neoprene. Silicone Acetate - std should not be used for sealing of aquaria. Silicone Acetate - std is not recom - mended for use on natural stone, such as marble, granite, quartzite, as it can cause staining. Silicone Acetate - std is not recommended for structural glazing bonding. Adhesion Silicone Acetate - std exhibits excellent primerless adhe - sion to most non-porous siliceous material, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker; impreg - nated, varnished or painted wood; and some plastics. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service. Processing The substrate areas that will be in contact with the seal - ant must be clean, dry and free of all loose material, dust, dirt, rust, oil, and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. Storage The ‘Best use before end’ date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intend - ed use must be checked for quality assurance reasons. Safety notes During vulcanization acetic acid is released. These va - pors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary. Should uncured silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, how - ever, can be handled without any risk to health.

89. 86 e xhaust p aste e xhaust a ssem B ly p aste Soft paste for fast, easy and totally gas tight • sealing of flanges and sleeve fittings in the exhaust system. No welding necessary. • The paste becomes metal hard, with exhaust • heat. Temperature resistant up to approx. 700°C. • Seals permanently. • Shock and vibration resistant. • No corrosion in joints, therefore easy disas - • sembly Content g Art. No. P. Qty. 140 0890 100 045 12 Small holes and cracks in the exhaust system • can be repaired easily. Extreme heat resistance. • Resistant to high temperature fluctuations. • Exhaust system may be repaired. • e xhaust putty Content g Art. No. P. Qty. 200 0890 100 046 10

21. 18 acrylic sealant White Clear Art. No. 9892.900.8 Art. No. 9892.900.9 Contents: 310 ml Contents: 310 ml Pack/Qty.: 1 Pack/Qty.: 1 All Weather Sealant is a multi-use sealant based on an advanced acrylic formula that provides the ultimate sealant technology for adhesion to all surfaces, application in wet weather and even to wet surfaces. The sealant remains permanently flexible and can be overpainted with most paints and wood stains when cured if required. Areas of Use For all roofline applications, adheres to problematic materials such • as lead, bitumen and galvanized steel. Ideal for sealing around lead flashing, gutters, downpipes and • corrugated roofing. For perimeter pointing to all window and door frames and all • weathersealing applications externally, ideal for timber frames where wood staining is requires. For sealing between metal and composite roof and wall panel forms • and effective lap joint sealant. For remedial sealing over all other sealants and old putties, mastic, • industrial metal panel sealing, caravan and automotive areas. White Art. No. 9892.900.5 Contents: 400 ml Pack/Qty.: 1 One Hour Caulk is a fast drying flexible decorators filler and sealant • that remains permanently flexible. Based on a high quality acrylic formulation One Hour Caulk can be • overpainted with all paint types or covered over with wallpaper. Painting can be carried out as soon as a skin forms, after • approximately one hour, no sanding down is required. Areas of Use For sealing and filling cracks and gaps between two different • substrates prior to decorating, the use of One Hour Caulk prevents unsightly cracks appearing at a later stage. Use around - skirting boards, ceiling cornices, window and door • frames, stair treads and risings, cupboards and other fixtures adjoining walls. Gaps, cracks and damage to plaster can also be filled using One • Hour Caulk. one hour caulk sealer a ll weather sealant

74. 71 thread lock & pipe sealant medium- strength screw fixer Screw fi xer and sealant – detachable Produces a medium-strength connection • Can be disassembled again using normal tools Curing guaranteed even on non-pretreated • parts Can also be used on uncleaned parts (e.g. in • their as-delivered state) Can also be used on stainless steel and • passivated surfaces No "accelerators" or "activators" required Excellent resistance to media and heat • Universal products with a wide range of poten - tial applications Prevents loosening due to e.g. vibrations and • impact stresses No unwanted locking prob - lems, e.g. as in the case of mechanical screw locks NSF-tested in accordance with NSF/ANSI 61 • Contents Art. No. P.Qty. 25 g 0893 243 025 1 50 g 0893 243 050 250 g 0893 243 250 Physical Properties (when liquid) Physical Properties (when hardened) Setting to the touch after 5 – 15 minutes Usable after 0.5–1 hour Final setting after 1–3 hours Break-loose torque > 21 Nm Just-move torque > 10 Nm Compression shear strength (DIN 54452) 8 - 12 N/mm 2 Temperature range –55°C to +150°C Chemical characterization Dimethacrylic ester Color blue/ fl uorescent Viscosity 25°C Brook fi eld RVT) 5.000–7.000 mPas (spindle rpm: 1/20) 1.500–2.500 mPas (spindle rpm: 3/20) Density 1.12 g/cm3 Max. thread diameter M 36 Max. gap fi lling capacity 0.25 mm Flash point > 100 ̃ Shelf life 1 year at room temperature

32. 29 fire cement Low modulus. Art. No. 892.317.999 Pack/Qty.: 1 Colour: White Description Fire rated, neutral cure sealant that retails integrity up to 4 hours • when exposed to extreme heat. Permanently flexible, offers movement aaccommodation of + or - • 50% with excellent adhesion to all substrates. Application Perimeter pointing to fire rated structures. • Vapour seals in fire rated cladding. • Pointing around curtain walling. • Sealing infill panels and concrete joints fire rated walls and floors. • Pyropol data Μovement Accommodation: + or - 50% Skinning Time: 4 to 8 hours Cure Time: 10 to 14 days Hardness Shore A: 15 Temperature Resistane: 150°C Paintability: not recommended Application Temperature: +30°C το + 60°C Cleaning: Uncured sealant with white spirit οr Μ.Ε.Κ. Shelf Life: 12 months Storage: +5°C to + 25°C Quantity estimator Number of catridges required = Lineal metres x cross section of joint in sq mm pack volume Joint dimensions Pyropol test compliance Pyropol has been tested to BS 476, Part 20 by the Loss Prevention Council, and Part 22 by Fulmer Yarsley. With the sealant applied to the exposed face of the furnace using Poyethylene Foam backer rod a single seal of PYrolpol achieved a 3 hour rating. Full copies of the test reports are available on request. Minimum joint width 5mm Maximum joint width 50mm Minimum joint depth 5mm Maximum joint depth 12mm Joint ratios Joint width 5mm 10 15 20 30 Joint depth 5mm 10 8 12 12 Joint size brick Applied brick to 32mm x 12mm Using 12mm P.E Foam = 4 hour rating 20mm x 12mm Using 12mm P.E Foam = 3 hour rating 20mm x 12mm Using 25mm ceramic fibre = 4 hour rating fire retardent silicone (pyropol)

25. 22 panel adhesive stixall - B ond and seal Permanently flexible adhesive and sealant Based on new hybrid PMS polymer technology - STIXALL is the ultimate building adhesive and sealant. It has the power to bond and seal virtually EVERYTHING to ANYTHING ! It offers almost limitless benefits as a permanently flexible adhe - sive and a sealant, removing the application barriers associated with conventional products. Incredible initial grab, no slip, gap filling. • High bond strength. • Exterior & interior use. • Can be applied to wet surfaces. • Totally waterproof. • Overpaintable. • Stops mould growth. • Solvent free. • Resistant to temperature extremes. • Resistant to chemicals. • Quick curing. • Applications; Bonds to virtually all materials porous and non-porous such as Glass, Marble, Granite, Mirrors, Bricks, Stone, Plaster Rose, Concretes, All Metals, All Hard Plastics, Ceramics, Fibreglass, Timber and much, much more... Art. No. Colour 01893 100 100 White 01893 100 101 Black 01893 100 102 Grey 01893 100 103 Brown 01893 100 104 Clear

38. 35 pu sealer seal / fix Sprayable sealant based on an MS polymer for recreating the original texture following accident repairs. Contains solvents.. Very broad adhesion range. Adheres to many surfaces, even without a primer coat. Great Shore A hardness. The material is impervious to mechanical loads. High tensile strength and elongationat tear. The seam also with stands stronger movements/ elongation. UV-stable. Excellent ageing behaviour, even when seams are not painted over. Suitable for painting over. Can be painted over “wet on wet” and up to five days after skin formation with any conventional painting system (except alkyd resin paints). After this period, another adhesion promoter (primer coat) must be applied for improved adhesion of the paint. Isocyanate- and silicone-free. Technical data: Chemical basis POP mixed polymer Density 1.48 g/cm3 Application temperature + 5 °C to + 30 °C Skin formation time (DIN 50014) 25 min Curing speed (DIN 50014) approx. 3 mm/24 h Shore A hardness (DIN 53505) 40 Temperature resistance – 40 °C to + 80 °C Storage temperature + 5 °C to + 25 °C Areas of application: Seam sealing in case of part replacement in the engine compartment, boot, floor group, spring strut, wheel well etc. Use: The application surfaces must be clean, dry, dust and grease-free. Seal/ Fix is applied with the pneumatic gun Combifix, Art. No. 0891 628 6. The desired textures and layer thicknesses are determined by the distance to the object/ the air pressure. Note: Do not allow Seal/Fix to come into contact with fresh polyurethane materials (i.e. those that have not yet hardened). If painting over with metallic paints, a blocking primer should definitely be applied. The best adhesion between the paint and the Seal/Fix is achieved when the material is painted over immediately following application. Color Look Contents ml Art. No. P. Qty. Schwarz 310 0893 226 1/12 White 310 0893 227 1/12 Gray 310 0893 228 1/12 Additional articles: Plastic nozzle for sprayable seam sealant, Art. No. 0891 628 612 2K Multi-Fill, Art. No. 0893 213 1 ! *measured at 23°C/50% rel. humidity

48. 45 w ood g lue Moisture curing one component adhesive to D4 (EN204). Areas of application Wooden door and window frame construction. • Lamination of wood materials e.g. MDF. • Furniture construction. • Structural adhesion of garden furniture. • Bonding of mineral building boards, ceramic materials and • concrete. Advantages One component. • Reacts with moisture from the air and from materials to be bonded. • Joint filling. • Resistant to solvents once cured. • Simple application. • Technical data Base: Isocyanate Colour: Yellow / brown Application quantity: 150 - 200 grams per M≤ Open time: 15 mins. at 20°C Clamping pressure: Min. 8 kg / M≤ Clamping time: 5°C - 120 mins. 20°C - 40 mins. 60°C - 15 mins. Full strength: 24 hours Gap filling capacity: Approx. 0.5 mm Cleaning: Uncured adhesive with 892.160 (PU Cleaner) cured adhesive can only be removed mechanically i.e. scraping. Working temperature: Ideal 20°C (min. 5°C) Moisture content of substrate: Max. 20%. Storage temperature: Between 10°C and 20°C. Shelf life: Approx. 9 months in closed airtight container. Method of use Surfaces must be clean, dry and free of dust and grease. It is advisable to wear protective gloves when using Polyurethane Glue as the glue reacts with moisture on the skin. Apply to one surface only at a rate of 150 - 200 grams per M 2 . Over application will result in wastage as the glue expands during curing. Clamping forces and times are as per the technical data. Contents Art No.: Pack/ Qty. 1kg 892.100.170 1 p olyurethane g lue

66. 63 e poxy resin a dhesive thick primer filler Corrosion protection with excellent fi lling and covering power for metallic surfaces. Very good adhesion properties. Adheres to aluminum, sheet steel, old paint etc. Long-lasting corrosion protection. Quick drying. Very good stretching and run off behavior. Heat-resistant up to 110°C. Very easy to sand. VOC*- compliant. Solvent-reduced. Complies with the maximum VOC content speci fi ed in the VOC Directive (1999/13/EC). * V olatile O rganic C ompound Features: Flexible thick primer fi ller with short dry-ing time, corrosion protection and very good adhesion properties, also in conjunction with PU and MS polymer sealing compounds. For professional repair of small uneven areas, scratches and traces of sanding. This information is only a recommendation based on our experience. Preliminary testing required! During use and painting over, both the technical data sheet and the speci fi cations of the top-coat paint manufacturer must be observed. Colour Contents in mL Art. No. P. Qty Gray 400 0893 212 1 1/6 Additional article Two-Component HS Top-Coat Paint Art. No. 5866 ... ... P. Qty. 1 Silicone Remover Spray, 600 mL Art. No. 0893 222 600 P. Qty. 6 ! Areas of application: Spot repair, accident repairs, vehicle body repair, paint work. Application: The application surface must be clean, dry and grease-free. Lightly sand problematic application surfaces. Shake can well before using. Apply the fi rst spray coating thinly. Comply with fl ash-off time. Can be painted over after about 15 minutes with all conventional one-component, two-component and water- based top-coat paint systems. Notes: Can be used on galvanized and hot-dip galvanized surfaces after pretreatment with Zinc Cleaner Art. No. 0893 460 under certain conditions. Turn can upside down and spray until valve is empty after use.

51. 48 w ood g lue smart tack smart tack is an advanced spray bonding system that outperforms and outdates conventional contact adhesives providing significant performance and time saving application benefits. Based on new technology resins, SMART TACK is applied by spray providing very fine strands of “high sol - ids” adhesive that forms a web type pattern on application. SMART TACK finds a multitude of uses in the Shopfitting, furniture manufacture, laminat - ing, joinery and exhibition industries. Smart tack bulk tank Designed for large scale use primarily in a production line environment, BULK TANK delivers the adhesive via a flexible industrial grade hose and high volume applicator gun. With excellent rapid covering ability, the BULK TANK GUN is left attached to the hose and canister and simply locked off after use with the system ready to go for instant re-use. The BULK TANK GUN and BULK TANK HOSE are sold as separate stock items. Both items, when used together, are fully interchangeable with most leading suppliers of similar systems. However, BULK TANK HOSE is com - patible with BULK TANK GUN only. Benefits Fast Tacking: - Surfaces can normally be “closed” after only 3-5 • minutes Long Open Time: - Surfaces can also be left open for up to • 2 hours. Immediate Handling: - High early bond strength allows item • to be handled, cut drilled and planed within 5 minutes of closing. High temperature: - Unaffected by temperatures up to 90 • o C (194`F). Fast Application; - 15 times quicker than applying • conventional contact adhesive by spreader. Cost effective: - Goes approximately three times further than • applying conventional contact adhesive by spreader. Convenient; - No airline, electric or press. Easy to maintain, • no mess. Safer: - Low odour, no CFC`s, self contained systems. • Blue Colour: - Unique to SMART TACK range. • Limitations Do not use in areas subject to continuous water immersion. Do not use on colour core laminates or on any translucent/opaque sheeting. Do not use on bitumen, asphalt, or cellulose painted surfaces. Do not spray directly onto polystyrene. Spray onto other surface. Do not use as a mirror adhesive as the product may attack the mirror backing. Use MIRROR MATE adhesive. Do not use in areas subject to intense lighting or sunlight where the sur - face temperature could exceed 90`C. At low temperatures, care must be taken to ensure that the temperature of the adhesive and of both surfaces to be bonded is higher than the ambi - ent temperature. Cold materials have a strong tendency to attract moisture present in surrounding air, which can have disastrous effects on the bond strength. Always allow adhesive to become touch dry on both surfaces. Premature bonding may cause solvent entrapment and blistering of laminates. As the manufacturer cannot know all the uses its products may be put to, it is the users responsibility to determine suitability of use. If in doubt, contact Technical Services Department for advice. Art. No. Description Pack Size Box Qty. 9893 100 017 Clear 17kg 1 9893 100 019 Blue 17kg 1 00891 602 001 Gun for Smart Tack n/a 1 00891 602 012 Hose for Smart Tack n/a 1 Areas For Use The adhesive gives a permanent bond on laminates, veneers, edge banding, vinyl’s, uPVC sheet and fabrics and may also be used for temporary/light duty bonding on carpets, fabrics, polystyrene/PU sheeting, posters etc.

45. 42 p olyurethane foam Cleaning kit for easy removal of cured PU foam from various surfaces. } Problem solver. Your advantage With this special kit you can easily clean • and remove contaminations of cured PU foam. } Non-dripping cleaning compound. Your advantage When applied to vertical surfaces, the • cleaning compound does not drop off. Thus, the cleaner can be applied selectively and the cleaning result is improved. } Wide range of applications. Your advantage Due to the good compatibility of the • cleaning compound, PU foam residue can be removed from various different surfaces, such as hard PVC, bright aluminium, glass and stone or ceramic materials. Note: Always perform a preliminary test with regard to the compatibility with the surface. Do not use on film-coated plastics, types of anodized aluminium and protective paint, as well as enamels, varnishes and similar surface protection. Stone and ceramic materials should have a sealed surface and not be porous or absorbent. Read the safety data sheet and instructions for use prior to application! Instructions for use Stir foam cleaner prior to use! As much as possible, carefully remove any foam residue mechanically. Apply the foam cleaner to the remainder, applying a full coverage. After a reaction time of 2 hours, scrape the PU foam residue off using a wooden spatula and applying light pressure. Finish cleaning the spot by rubbing with a moist cloth. If required, repeat the procedure. To improve the glossy finish of the surface afterwards, apply PVC Gloss Care. Make sure to read the enclosed instruction sheet! Storage The chemical products contained in the cleaning kit have a shelf life of 12 months when stored in a dry place (+ 5°C to + 25°C). Refer to container markings. Application This information is only intended as a recommendation based on our own experience. The user should always perform his own preliminary testing. Designation Article Number Pack/Qty. 1 can (150ml) foam cleaner 892.160.000 1 1 bottle (250ml) PVC glass care 1 wooden spatula 1 cleaning cloth 1 instruction sheet Scope of supply Note: The individual articles are not available separately! purlogic foam cleaner

59. 56 w indscreen a dhesive "classic plus " windscreen a dhesive Elastic 1-component windscreen adhesive with very good stability. Normal-modulus Can be used for all common vehicle types in the car, utility • vehicle, bus, transport vehicle and agricultural and construc - tion machine sectors. Suitable for antennas, non-conductive.Prevents contact corrosion. Suitable for use on aluminum, magnesium and hybrid vehicle • bodies (e.g. Audi A8, Jaguar XJ etc.). Tested safety Drive-away time confirmed via crash testing and TÜV certifi - • cate pursuant to FMVSS208/212! Meets requirements of original equipment manufacturers • (motorvehicle manufacturers). Areas of application: Replacement glazing of cars, utility vehicles, buses, transport vehi - cles and agricultural and construction machines. Use: It is imperative that the Würth Active Cleaner and the Würth Varioprimer be used when preparing surfaces. The products are to be checked to ensure that they have not expired before they are used. Apply adhesive while guiding the gun vertically, starting from the center at the bottom of the windscreen. Do not place the vehicle on the lifting platform. Observe the information provided by the vehicle manufacturer in regard to bead geometry. The application and drive-away times must be observed. Note: It is imperative that the Würth Active Cleaner and the Würth Varioprimer be used when preparing surfaces. The products are to be checked to ensure that they havenot expired before they are used. Apply adhesive while guiding the gun vertically, starting from the center at the bottom of the windscreen. Do not place the vehicle onthe lifting platform. Observe the information provided by the vehi - cle manufacturer in regard to bead geometry. The application and drive-away times must be observed. Designation Contents Art. No. P.Qty. Complete Set * 0890 023 700 1 Cartridge 310 mL 0890 023 701 1/12 Professional Set ** 0890 023 710 1 Bag 400 mL 0890 023 711 15 * Set = cartridge, Active Cleaner (double cloth), Varioprimer safe + easy (20 mL), priming brush, window application nozzle, repair instructions. ** Set = bag, Active Cleaner (double cloth), Varioprimer safe + easy (20 mL), priming brush, window application nozzle, repair instructions. This information is only a recommendation based on our experience. Preliminary testing required! For further information see the technical information leaflet. Basic information ULTIMATE Chemical basis 1K polyurethane (moisture - hardening) Color black Application temperature +5°C to +35°C Processing time 15 min.* Storage temperature +5°C to +25°C Drive-away time w/o airbag 1 hr.* Drive-away time w/airbag 2 hr.* measured at 23°C/50% rel. humidity. Additional article Active Cleaner, 500 mL Art. No. 0890 024 1 Varioprimer, stick, 10 mL Art. No. 0890 024 010 Varioprimer, bottle, 20 mL Art. No. 0890 024 021 Varioprimer, bottle, 100 mL Art. No. 0890 024 101 !

16. 13 s ilicone s ilicone c olour High-quality multifunctional sealant in individual RAL colors. Available in individual RAL colors The color option (approx.180 RAL colors) offers unlimited design possibilities for indoor and outdoor expansion and connecting joints. Anti-fungal properties 1 Prevents mold especially in plumbing applications Adhesion spectrum Can be used on virtually all common construction surfaces Properties: Certi fi ed in accordance with DIN ISO 11600 F-25HM • Material Class B2 according to DIN 4102 • Without softeners, therefore suitable for use on natural stone • Permanently elastic • UV-resistant • Compatible with paint • Weather-resistant • 1 The permanence of the anti-fungal effect is dependent on the moisture load and the ventilation behavior. Container Contents ml Art No.: Pack / Qty. Cartridge 310 ml 0892 580 0 12* Typical application surfaces: Without primer: Glass, aluminum (untreated, painted, glazed), all types of metal, enamels, tiles, glazed ceramic, natu - ral stone (e.g. granite, marble), wood, a broad range of plastics With silicone primer: Concrete, aerated concrete, chalky sandstone, clinker, brick, gypsum and plaster (observe informa - tion in the building material compatibility table for sealants) Color options: All RAL colors in accordance with the RAL Color Card (Art. No. 0705 800 010) are available, except for all neon and metallic colors. Attention! Silicone Color is a special product for individual customers. For production reasons, minor fl uctuations in the color can occur. This is not a product defect. No exchange possible. Carry out color matching with existing material prior to application. Notes: Cannot be painted and plastered over. Not suitable for use underwater or in aquariums. Does not adhere to polypropylene, polyethylene, PTFE and bitumen. Silicone Color is not suitable for adhesive bonding or fi lling hollow spaces. Due to the large number of existing paint and glazing formulas, especially on alkyd resin paints and powder-coated aluminum, it is necessary to conduct an adhesion check with your own tests. Danger of yellowing on contact with white alkyd resin paints cannot be excluded. *Minimum quantity 24 pcs. Possible Uses

57. 54 s uper g lue spray adhesive Fast-drying adhesive for all lightweight materials. ► Highly temperature-resistant. Your advantage: Permanent firm hold for almost all applications. ► Fast-drying. Your advantage: Thanks to fast hardening, working material can already be loaded and processed further after a short time. ► Adjustable spraying nozzle. Your advantage: Optimal for use in an extremely broad range of work situations. ► Silicone-free. Areas of application: Permanently and quickly bonds plastic, foam, cork, foils, metal, wood, paper and polystyrene with and to each other. Especially suitable in motor vehicle sector, inplant workshops, in switch cabinet and ventilation system construction etc. Notes: Thin application of adhesive;saturate well on absorbent surfaces. Flash-off time depending on surface, materialand temperature: 5–10 minutes. Caution: Not suitable for adhesive bonding of soft PVC and PVC films. Designation/Container Contents ml Art. No. P. Qty. Aerosol can 500 0890 100 055 12 high - adhesion spray adhesive Designation/Container Contents ml Art. No. P. Qty. Aerosol can 500 0890 100 064 12 Film-forming adhesive with high immedi - ate adhesive bonding force for absorb - ent surfaces. Areas of application: Permanently and quickly bonds plastic, metal andin special absorb - ent surfaces, e.g. felt, fabric, foam and woven fabric, with and to each other. The adhesive bonding properties are especially matched to the various applications in the motor vehicle sector. Notes: Shake well before using. The parts to be bonded must be dry and free of dust and grease. Following cleaning, thinly spray both glu - ing surfaces at a distance of approx. 20–25 cm; saturate well with absorbent surfaces. Allow to flash off for between 5–15 min. (depending on temperature, material and application) and join. Caution: Not suitable for adhesive bonding of soft PVC, PVC films and Styrofoam. Acetone Cleaner Art. No. 0893 460 Precleaner Art. No. 0893 200 1 Silicone Remover Art. No. 0893 222 Art. No. 0893 222 5 ! We provide this information to advise you based on our tests and experience to the best of our knowledge. Preliminary testing required! For additional information, see Technical Data Sheet.

88. 85 gasket sealer silicone special Cold-vulcanizing silicone rubber. • Permanently elastic silicone sealing com - • pounds for engine and vehicle body. For sealing surfaces, gaps and cracks in water • pumps, oil pans, coolers, crankcases etc. Bridges larger rough areas. • Seals reliably, even after with standing years • of vibrations. Outstanding adhesion. • Does not run or draw threads. • Outstanding resistance to chemicals. • Skin formation after just a few minutes, vulcani - • zation duration approx. 1.5mm/day. Areas of use: Separating joints, cylinder head, crankcase, • water pump, oil pan, cooler, axle tube, cylin - der base (motorcycle), lamp and blinker hous - ing, weld seams etc. Colour Content Art. No. P. Qty. Transparent 100 g /70 ml 0890 320 10 Blue 0890 322 Silicone Special 180 Silicone Special 250 Colour Content Art. No. P. Qty. Red 100 g /70 ml 0890 321 10 Black 0890 323 Thermally stable from – 50°C to + 150°C brie fl y • up to + 180°C. Thermally stable from – 50°C to + 250°C brie fl y • up to + 300°C.

83. 80 a dhesive tapes a utomotive sealing tape Automotive sealing tape protects against vibration and will seal gaps securely and permanently in one go. After release of the compression the tape will expand and develop a pressure which firmly presses against the gap surfaces and levels up uneven parts. Pre-compressed. • Self adhesive on one side. • Temperature resistance: –30°C to +90°C. • Advantages Can by painted over with commond is persion • lacquers. Open to diffusion, thus avoiding of water • accumulation Assembly Instructions Clean the gap/surface from oil, grease and • loose particles. Remove cover paper from the sealing tape. • Adhere sealing tape to the surface or apply • directly from the roll to the gap. Assembly Instructions Sealing and protecting parts against vibration • in ventilation and heating systems, tanks, frame supports or lateral supports of the boot lid etc. To protect against vibration when fitting radios • and speakers etc. For coating aerial cable (i.e. VW, Ford). • Automotive Sealing Tape Width Thick 1) Thick 2) mm mm mm Gap width mm Roll length m Art No Pack Qty 10 2 10 2-3 12.5 0875 410 2 1 20 2 10 2-3 12.5 0875 420 2 115 3 15 3-4 10.0 0875 415 3 15 4 20 4-5 8.0 0875 415 4 1) Thickness compressed to 20%. 2) Thickness when expanded.

93. 90 a dhesive cleaner industr y cleaner High-quality special cleaner for industry and craft trades. Simple removal of adhesive residues, labels • and adhesive tape. Stubborn soiling like wax, rubber abrasion, • silicone residues, permanent marker, oil and grease are dissolved. Gentle on materials. Sensitive surfaces such as aluminum, brass • and stainless steel are not attacked. User-friendly No unpleasant odours for user and • environment. Quick and effective cleaning. • Acetone-free. Silicone-free and AOX-free Additional articles Film eraser Art. No. 0585 91 ! Areas of application: Removes adhesive residues from machine parts, plastic parts and metallic surfaces. Also suitable for removing protective preservatives e.g. on brake discs or for pre-cleaning of adhesive bonds. Note: Check rubber and plastic parts for compatibility in a location not visible prior to treatment. Paints may be attacked. This information is only a recommendation based on our experience. For further information, see the technical information lea fl et. Designation Contents Art. No. P. Qty. Aerosol can 500ml 0893 140 1/12 Canister 5 L 0893 140 05 1 Pump Spray Bottle, Neutral - 0891 501 Tap - 0891 302 01 REFILLOmat Designation /Container Contents Art. No. P. Qty. REFILLOmat can 400ml 0891 881 16 1/12 REFILLOmat canister 20 L 0893 140 520 1 REFILLOmat station - 0961 891 023

23. 20 panel adhesive multistick panel adhesive A high quality, one part gunable SBR adhesive (synthetic butyl rubber). • Ideal for panel and batten bonding. • High body gives gap filling properties. • Excellent bonding characteristics. • Fast panel construction without nails, screws or fixing strips. • High slump resistance. • Uses This highly versatile adhesive will permanently bond panel materials, insulation products, carpets grippers etc. most building surfaces. DO NOT USE with expanded polystyrene. Technical data Product type: filled polychloroprene / phenolic resin Colour: pale cream. Viscosity: heavy paste. Clean up solvent: 8901.100.026 Flash point: -22°C (-8°F). Application 1) Preparation (for maximum bond integrity) Precondition adhesive and materials to be bonded @ 15°C - 20°C (60°F - • 68°F). Surfaces should be free of grease and dust. • 2) Gunning Cut nozzle to give required line size (3 - 6 mm dia.) depending on gap to be • filled. Pierce inner seal. Apply lines of adhesive at approx. 30 cm centres to surface to be bonded. • Assembly For light panel materials press firmly onto adhesive immediately and leave to set. For heavier materials or those with pronounced bowing, press firmly onto adhesive as above, then break bond and hinge panel away. Allow panel adhesive to dry for 10 - 20 minutes depending on adhesive coating and ambient conditions. Remake bond. Press well, preferably using mallet or wood block to ensure firm bond. Maximum adhesive performance is dependent on sufficient pressure being applied. Handling precautions Do not smoke. Keep away from all other sources of ignition. 1. Use only in well ventilated areas to conform with the current Occupational 2. Exposure Limits. Avoid breathing vapours. Avoid contact with skin and eyes. Wear suitable protective clothing, 3. impervious gloves (e.g. of neoprene or nitrile rubber) and goggles. To meet BS 2092. Store in a secure environment away from sources of ignition.If in confined 4. space, the vapour will cause drowsiness. A localised extraction system using flameproof equipment must be used. Alternatively suitable respiratory equipment must be worn. Description Contents ml Art No.: Pack/ Qty. Cartridge 380 892.151 1 Storage Ideal storage temperature 15°C - 20°C (60°F - 68°F). DO NOT STORE BELOW 10°C (50°F). Storage - 6 months in closed containers @ 20°C (68°F) under cover in a dry area. Note: Temperatures above 20°C (68°F) will reduce storage life. Health and safety For further information please consult the relevant Würth Ireland Ltd. Hazard Data Sheet.

34. 31 pu sealer B ond and seal Elastic PU adhesive and sealant for a broad range of uses. ► For universal use. Your advantage: Outstanding adhesive strength on a wide range • of materials and surfaces. ► Highly elastic. Your advantages: Can be used for connecting same and different • materials. Compensation of different material expansions. • Dampens vibrations and noise. • ► Long skin formation time. Your advantages: Enables bolding and/or sealing of complicated • and very large components. Joint parts can be repositioned. • ► Can be ground and painted over. Your advantage: Following skin formation, can be mechanically • machined and painted over without surface activation (check paint compatibility beforehand with preliminary tests!). ► Legally approved for use with food (ISEGA certificate). Your advantages: Harmless to humans in hardened state. • Suitable for bonding and sealing food process - • ing plants. ► Non-corrosive. Your advantage: Prevents metal corrosion. Nearly odourless. ► Silicone-free. Replacement Nozzle Art No.: 0890 100 099 P.Qty. 12

20. 17 acrylic sealant acrylic sealant Can be smoothed with water and over-painted. For sealing Joints where strain and expansion requirements are low. • Connecting and sealing joints in interior extensions. • Cracks in walls, plaster, concrete. • Adhesion of stropore. • Not suitable for glazing in window installations or for expansion joints and substrates • such as glass, enamel and ceramic. Limited outdoor applications, as it is soluble in water in un-hardened state. • Properties Single component sealant based on dispersed acrylic resin. • Free of solvents and silicone. • Resistant to ageing, weather and UV rays once hardened. • Can be painted over with commercially available colours and lacquers. Individual test • necessary. Good adhesion on various building materials such as concrete, porous concrete, plaster, • walling, asbestos cement, wood, plasterboard, etc. Please note: The substrate must be clean and free of frost and grease. The joint should be approximately half as deep as it is wide. The correct depth of the joint should be achieved by re-filling with foam material. This will also prevent three-point adhesion. Acrylic sealant should not be over painted before it has hardened. A subcoat will improve adhesion on porous and absorbent substructures such as cement, concrete, etc. Sub coat is between 1:1 and 1:5 acrylic sealant to water. Technical Data Raw material base: Acrylic resin dispersion Shelf life: at + 20°C, 1 year (protect from frost) Skin formation time (finger test): approx. 15 min. at + 23°C and 50% rel. air humidity Shore hardness A: approx. 30 Recovery: approx. 50% Density: 1.5 g/cm≥ Working temperature: + 5°C to + 40°C Temperature resistance: - 25°C to + 80°C Hardening rate in 24 hours at + 23°/ 50% rel. air humidity: approx. 1 min. Permanent expansion: approx. 10% Elongation at fracture: approx. 150% after 7 days storage at room temperature & 7 days at 50°C Change in volume: approx. 15% Notes on handling: Avoiding three point adhesion: When applying a sealant, care must be taken to ensure that it adheres on a substrate. Stress cracking can result from movement and a 100% seal of the joint should be achieved by using a backfill material to avoid three-point adhesion. Edge 1 Backfill Material Substrate Edge 2 It is our intention to advise you to the best of our ability, drawing on past experience and tests. However, due to the variety of applications and the conditions governing storage and application, which lie outside our control, we are not in a position to accept responsibility for individual results. This also applies if our non-binding technical and customer service is availed of. We always recommend individual tests. Consistent quality of our products is guaranteed. Subject to technical modifications and further development. Colour Illu. Contents ml Art No.: Pack/Qty Beige 310ml 892.164 1 White 9892.900.1 Brown 9892.900.2 Sealant

4. 1 s ilicone silicone sealants Top quality acetoxy curing silicone. Conforms to BS 5889 type B. DIN 18545 part 2. Neutral curing for use with PVCu. Conforms to ISO 11600, BS 5889 type A. All colours contain fungicide except transparent. All colours contain fungicide except transparent. Please note: All Art. No. are available as single items. Colour Art. No. Transparent 0892 317 1 White 0892 317 2 Grey 0892 317 3 Brown 0892 317 5 Black 0892 317 6 Beige 0892 317 9 Aluminium 0892 317 10 Bronze 0892 317 20 Colour Art. No. Transparent 0892 310 1 White 0892 310 2 Black 0892 310 5 Brown 0892 310 6 Oak 0892 310 9 Bronze 0892 310 14 Colour Art. No. Transparent 0892 317 71 White 0892317 72 Brown 0892 317 75 Standard Grade 310 ml Low Modulus 310 ml Neutral Curing 310 ml

6. 3 s ilicone l ow modulus silicone Art. 00892 317 71 Product description One-component, acid-curing, low-modulus silicone seal - ant for glazing and industrial applications. Low Modulus Silicone cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Special features solvent-free • non-sag • ready gunnability at low (+5°C) and high (+40°C) • temperatures low shrinkage on curing • flexible at low (-40°C) and high temperatures • (+180°C) low-modulus: better adhesion and higher safety • rapid crosslinking: quickly becomes tack-free • adheres excellently to glass, vitrified surfaces, • ceramic tiles, many plastics and most paints excellent tooling properties • long shelf life • Application glass and windows construction • sealing of joints between glazing and supporting • structure (frame, tansoms, mullions) industrial application as sealant in the automotive, • aircraft and shipbuilding industries Restrictions on use Low Modulus Silicone should not be used on substrates such as marble, concrete, fibrous cement and mortar, as the product releases acetic acid during vulcanization. Low Modulus Silicone should not be used in contact with metals such as lead, copper, brass or zinc due to corro - sion. Low Modulus Silicone may be discolored in contact with some organic elastomers, e.g. EPDM, APTK and neoprene. Low Modulus Silicone is not recommended for sealing of aquaria, please use our Low Modulus Silicone. Low Modulus Silicone is not recommended for use on natural stone, such as marble, granite, quartzite, as it can cause staining. Low Modulus Silicone is not recommended for structural glazing bonding. Adhesion Low Modulus Silicone exhibits excellent primerless adhe - sion to most non-porous siliceous material, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker; impreg - nated, varnished or painted wood; and some plastics. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service. Processing The substrate areas that will be in contact with the seal - ant must be clean, dry and free of all loose material, dust, dirt, rust, oil, and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. Storage The ‘Best use before end’ date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intend - ed use must be checked for quality assurance reasons. Safety notes During vulcanization acetic acid is released. These va - pors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary. Should uncured silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, how - ever, can be handled without any risk to health. Comprehensive instructions are given in the correspond - ing Material Safety Data Sheets.

14. 11 s ilicone silicone neutral Art. 00892 310* 1 / 2 / 5 / 6 / 9 Product description Silicone Neutral is a one-part, neutral-curing, low modu - lus silicone sealant with good adhesion and long shelf life for DIY-sector. Properties Silicone Neutral cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber Special features long shelf life • primerless adhesion to most materials • non-corrosive to metals • suitable for alkaline substrates such as concrete, • mortar, fibrous cement almost odorless • non-sag • ready gunnability at low (+5°C) and high (+40°C) • temperatures rapid crosslinking: quickly becomes tack-free • flexible at low (-40°C) and high temperatures • (+120°C) good weatherability • Application sealing of low stress connection and expansion joints • in the building industry - sealing of low stress perim - eter joints Restrictions on use Silicone Neutral must not be used as a secondary seal - ant in insulating glass units. Silicone Neutral must not be used for structural glazing bonding. All building materials that come in contact with Silicone Neutral such as solid adjacent substrates, liquids or gaseous vapors of other building materials must be compatible with Silicone Neutral and must not trigger any chemical or physical changing that might result in discoloring of the sealant or deterioration of its functional capability. For any arising inquiry about the compatibility of building materials with Silicone Neutral please consult the building material’s manufacturer. Silicone Neutral is not suitable for use on natural stones, such as marble, granite, quartzite, as it can cause staining. Silicone Neutral is not recommended for sealing of aquaria or for the longer-term use under water. Silicone Neutral is not suitable for food contact applica - tions. Silicone Neutral is not suitable for use as a mirror adhesive. The time until complete curing may be extend - ed at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange. Adhesion Silicone Neutral exhibits good primerless adhesion to most of the substrates used in DIY-applications, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker; metals, e.g. aluminium, steel, zinc or copper; impregnat - ed, varnished or painted wood; and many plastics. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service. Processing The substrate areas that will be in contact with the seal - ant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non- porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. Storage The ‘Best use before end’ date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intend - ed use must be checked for quality assurance reasons. Safety notes During vulcanization ethanol is released. These vapors should not be inhaled for long periods or in high con - centration. Hence, good ventilation of the work place is necessary. Should unvulcanized RTV-1 silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, however, can be handled without any risk to health. Keep away from children.

81. 78 a dhesive tapes B utyl t ape Strongly adhesive, double-sided sealing tape made of butyl rubber for overlapping seals. Very good compatibility with all known surfaces. Very good compatibility with metals, concrete, • masonry, wood, glass, hard PVC, bitumen, paint systems, as well as very good adhesion proper - ties, makes a number of combinations in sealing systems possible. Excellent resistance to UV, weathering and water. For both indoor and outdoor use. • Additional properties Impermeable to vapor diffusion. • Self-fusing. • Compatible with Plexiglas and Macrolon. • Fields of application: For the connection of seams and the gluing of vapor • barrier fi lms. Overlapping seals for vehicle and roof mounting parts, for • facades and equipment construction, in the furniture and interior design industry, for sanitation and electrical instal - lations, and all similar applications. B utyl round cord For the round butyl cord, the same product tech - • nical properties as in the case of the butyl tape (Art. No. 0894 700 122 / 202) apply. Fields of application: Fastening of mounting parts of vehicles, such as • the gluing of lower door cover fi lms, attachment of decorative moldings. Sealing of storage tanks, silos, roofs made • of trapezoidal plates, and others to prevent vibrations. All overlapping seals as with butyl tape (see • above). Ideal use on uneven foundations. • With this information we want to advise you to the best of our knowledge based on our tests and experience. We assume no liability for the application results in individual cases, however, due to the large number of applications and the storage and application conditions that lie outside the scope of our influence. This also applies to the use of the non-binding technical and commercial customer service we provide. We always recommend that you conduct your own tests. We guarantee the consistent quality of our products. We reserve the right to make technical changes and carry out further development. For further information, see the Technical Data Sheet. Width in mm Length in mm Thickness in mm Art. No. P. Qty. 12 15 2 0894 700 122 1 20 15 2 0894 700 202 Dia in mm Length in mm Art. No. P. Qty. 3 5 x 16 (80) 0894 700 380 1

12. 9 s ilicone silicone neutral Art. 00892 310 14 Product description Silicone Neutral Premium is a one-part, neutral-curing, low modulus silicone sealant with excellent adhesion and long shelf life for perimeter sealing and glazing and sanitary applications. Properties Silicone Neutral Premium cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Special features suitable for use in sanitary areas • long shelf life • primerless adhesion to most materials • non-corrosive to metals • suitable for alkaline substrates such as concrete, mortar, fibrous cement • almost odorless • non-sag • ready gunnability at low (+5°C) and high (+40°C) temperatures • rapid crosslinking: quickly becomes tack-free • flexible at low (-40°C) and high temperatures (+150°C) • excellent weatherability • Application sealing of connecting and expansion joints in the building industry • sealing of joints in sanitary applications • sealing of perimeter joints • Restrictions on use Silicone Neutral Premium must not be used as a secondary sealant in insu - lating glass units. Silicone Neutral Premium must not be used for structural glazing bonding. All building materials that come in contact with Silicone Neutral Premium such as solid adjacent substrates, liquids or gaseous vapors of other building materials must be compatible with Silicone Neutral Premium and must not trigger any chemical or physical changing that might result in discoloring of the sealant or deterioration of its functional capabil - ity. For any arising inquiry about the compatibility of building materials with Silicone Neutral Premium please consult the building material’s manufac - turer. Silicone Neutral Premium is not suitable for use on natural stones, such as marble, granite, quartzite, as it can cause staining. Silicone Neutral Premium is not recommended for sealing of aquaria or for the longer-term use under water. Silicone Neutral Premium is not suitable for food contact applications. When using Silicone Neutral Premium in permanently wet areas where the joint is strongly or permanently exposed to water, e.g. in swimming pools or public sanitary facilities, please contact our technical service. Silicone Neutral Premium is not suitable for use as a mirror adhe - sive. The time until complete curing may be extended at lower temperature, lower humidity, increasing film thickness or by low volume of air exchange. Adhesion Silicone Neutral Premium exhibits excellent primerless adhesion to most material used for sanitary application, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker; on metals, e.g. Aluminum, steel, zinc, copper, on varnished or painted wood; and some plastics. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service. Processing The substrate areas that will be in contact with the sealant must be clean, dry and free of all loose material such as dust, dirt, rust, oil and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. Storage The ‘Best use before end’ date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties re - quired for the intended use must be checked for quality assurance reasons. Safety notes During vulcanization ethanol is released. These vapors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary. Should unvulcanized RTV-1 silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, however, can be handled without any risk to health. Keep away from children.

22. 19 acrylic sealant upvc gap filler & sealant Seals and Protects ! Seals and joins gaps between rigid PVC, brickwork. • Water resistant. • UV stabilised. • Bacteria resistant. • Cures rapidly to provide a colour fast finish. • Not suitable for use on expanded or foil wrapped PVC or PVC • trim. Shelf life: see expiry date on tube or outer packaging. • Methods of use Mix of PVC resins and solvents, suitable for bonding many • materials including rigid and plasticized PVC and coated metals. Widely used in the window industry for frames and • attachments. Once cured it has no smell, retains its flexibility in use for any • long periods of time. Good slump resistance. • Sealed joints move with the substrate and remain water-tight. • The UPVC Gap Filler & Sealant is quite viscous and has very • good gap filling properties. Directions for use Ensure surfaces to be bonded are clear, dry and free from • grease by cleaning with the UPVC Gap Filler & Sealant. Where bonding without gap filling being required, one surface • should be coated lightly with adhesive and brought together whilst still wet. For gap filling use the UPVC Gap Filler & Sealant. • Apply a thick layer of filler and allow for shrinkage after • curing. Care must be taken to ensure that solvents can evaporate • freely. Due to the variety of materials on the market and the fact that • Würth Ireland Ltd. cannot know all the uses that its products are put to. It is the user’s responsibility to determine suitability of use and • compatibility with the products being bonded or sealed. Description Colour Contents g Art No.: Pack / Qty. Cartridge White 300 01892 030 1

53. 50 s uper g lue Content g Art. No. P. Qty. 5 g 0893 090 0 1/25 20 g 0893 09 1 50 g 0893 090 1 super fast glue For the adhesion of metal, plas - tic, and rubber parts with and to each other. ► Patented special cap. Your advantages: Problem-free, one-handed use. • Precise dosing. • The tips do not clog. • ► Bonds in seconds. Your advantages: Immediate further processing possible. • Fast repairs. • Simple designs without additional fastening • materials possible. lncreased temperature usually not necessary. • ► Solvent-free. Attention: It is advisable to wear safety gloves and goggles. Content g Art. No. P. Qty. 30 g 0893 090 030 1/16 super fast glue Now, also in the innovative EASY PEN design. Even easier, more practical handling. • Fits ergonomically in your hand. • The base of Easy Pen provides stable, secure • support. The lever permits easy, problem-free use with - • out great force. High-precision work possible. • Nitrile Disposable Glove Art. No. 089947003 Comfort Assembly Glove Art. No. 08994006.. Polycarbonate Goggles Art. No. 08991020 !

55. 52 s uper g lue Benefits Flash setting formulation - bonds most surfaces • within 10 seconds, cutting down dramatically mitre assembly bonding times when compared to conventional wood adhesives. High viscosity adhesive – low soak in to give • greater bond strength than conventional cyano - acrylates on porous surfaces (eg wood) Gap filling – high viscosity adhesive will fill • small gaps in mitres etc (up to 0.2mm) Economical in use. • Areas of Use Multitude of industrial applications: Bonds MDF, • wood, chipboard, rubber, plastics, Perspex, uPVC ceramics, aluminium and metals. Ideal for all cornice and profile mitres, trims, • picture frames, MDF, skirting and architrave joints, worktop end strips, PVCu trims and much more. It is particularly useful for production lines such as electronics assembly and uPVC window trim bonding. Limitations Ensure surfaces are degreased prior to bond - • ing. Do not use on glass • Do not use in applications involving constant • water immersion. Do not use on bitumen or tar leaching products. • Do not use on load bearing applications – Use • EVERBUILD ALL PURPOSE WOOD ADHESIVE. On wooden/porous surfaces, do not use any • other cyanoacrylate except MITRE FAST ADHE - SIVE. These products are thinner and the soak in will give poor bond strength. Shelf Life Six to Twelve months from date of manufacture • in original unopened containers, depending on temperature of storage. As low temperature as possible will give maxi - • mum shelf life. Application Spray one surface with activator. • Apply adhesive sparingly to other surface • Bring together, position and hold for about 10 seconds. • Storage Store in original unopened containers between 4 and • 25 o C. Reseal immediately once used. Protect activator from sources of ignition • Contents: 50g 200ml ever B uild mitre - adhesive and activator Art. No.: 01893 212

76. 73 thread lock & pipe sealant pipe sealant For the sealing of all metallic pipe connections and fittings with conical/cylindrical threads pursuant to DIN 2999. Content Art. No. P. Qty. 50 g 0893 577 050 1 Content Art. No. P. Qty. 50 g 0893 511 050 1 250 g 0893 511 250 Physical Properties Mid-strength product Low-strength product with PTFE ► Tested quality. Your advantages: DVGW-approval (Reg. No. • NG-5146BM0336+0037), tested in accordance with DIN EN 751-1. NSF-tested pursuant to NSF/ANSI • 61. Tested oxygen compatibility up to • 60°C and 10 bar oxygen pressure (pipe sealant). ► Immediate sealing at up to 5 bar. Your advantage: Tightened connections can be loaded • up to approx. 5 bar. After final hard - ening, they can be loaded up to the burst pressure of the pipes. ► Great media resistance. Your advantage: Neutral behavior in comparison to • most industrial liquids and gases. Other advantages: ► Solvent-free. ► Sealing compound does not leak out of thread. ► Quick and secure mounting. Use: The thread must be dry, dust and grease-free and capable of bearing loads. Tighten it (> 5 Nm), but do not turn the thread further. Note: Not suitable for screw connections containing copper (brass, bronze, red brass) that come into contact with water over 40°C. Not permitted for gas connections in buildings in Germany. Pursuant to TRGI ’86/96. The thread must be cut in accordance with the stan - dard. During and after hardening of the product, the connections may not be rotated, i.e. read justment is not permissible.

43. 40 p olyurethane foam Use for fastening wooden door frames, filling and sealing window • sills etc., for insulating and filling-in wall gaps and other cavities. An assembly and filler foam containing an environmentally safe • propellant mixture in accordance with the Montreal Protocol for the protection of the ozone layer. Basis is one-component polyurethane prepolymer curing on • contact with moisture. Contents: 750 ml Art. No: 892.155.1 Pack/Qty.: 1 Properties The fresh foam adheres to all building materials with the exception • of surfaces such as polyethylene, teflon, silicone, oils and greases, mould release agents and similar. It can be used at temperatures from +5°C approx. upwards to • +25°C approx. The cured foam is semi-rigid and predominantly close celled. • It is resistant to heat and cold (-40°C to +100°C) and to ageing, • but not to UV rays. The 500 ml container gives a yield of approximately 22 litres, • which is sufficient to fill approximately 5 door frames (depending on slot width). Preparation The surfaces must be clean, firm, free of loose particles and free of • dust, grease and mould release agents and similar. Immediately before applying the foam, the surface must be • sprayed thoroughly with water needed for an even curing of the fresh foam. Atmospheric moisture alone is not sufficient. Expansion is helped by further moistening each layer of fresh foam • during the application process. The ideal processing temperature of the can and surface is • approx. +20°C. Screw the adaptor with the extension hose firmly onto the valve, • up to the stop, but do not over-tighten. CAUTION: Take care not to operate the valve accidentally. Shake well, approximately 15-20 times before use. Application The foam flow can be regulated accurately by applying different pressure or by tilting • the adaptor with the valve pointing downward. Activate the valve lever carefully and regulate the foaming. • The fresh foam will expand by approx. 100-150%. • Over-filling a joint will result in a prolonged curing process and insufficient air or surface • moisture may cause delayed expansion. Note: For further technical information please see next page. Please note: Remove fresh foam spills immediately with PU Cleaner or solvents such as acetone. Cured foam can only be removed mechanically. fix & fill foam

8. 5 s ilicone l ow modulus silicone Art. 00892 317 72 / 00892 317 75 Product description One-component, acid-curing, low-modulus silicone seal - ant for glazing and industrial applications. Low Modu - lus Silicone cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber. Special features mold retardant • solvent-free • non-sag • ready gunnability at low (+5°C) and high (+40°C) • temperatures low shrinkage on curing • flexible at low (-40°C) and high temperatures • (+180°C) low-modulus: better adhesion and higher safety • rapid crosslinking: quickly becomes tack-free • adheres excellently to glass, vitrified surfaces, ce - • ramic tiles, many plastics and most paints excellent tooling properties • long shelf life • Application glass and windows construction • sealing of joints between glazing and supporting • structure (frame, tansoms, mullions) sealing of joints exposed to high levels of moisture, • e.g. sanitary field industrial application as sealant in the automotive, • aircraft and shipbuilding industries Restrictions on use Low Modulus Silicone should not be used on substrates such as marble, concrete, fibrous cement, and mortar, as the product releases acetic acid during vulcanization. Low Modulus Silicone should not be used in contact with metals such as lead, copper, brass or zinc due to corro - sion. Low Modulus Silicone may be discolored in contact with some organic elastomers, e.g. EPDM, APTK and neoprene. Low Modulus Silicone must ot be used for sealing of aquaria. Low Modulus Silicone is not suitable for applications involving contact with natural stone, such as marble, granite, quartzite, as it can cause staining. Low Modulus Silicone is not suitable for insulating ap - plications. Adhesion Low Modulus Silicone exhibits excellent primerless adhe - sion to most material used for sanitary application, e.g. glass, tiles, ceramics, enamel, glazed tiles and clinker; varnished or painted wood; and some plastics. Users must carry out their own tests due to the great variety of substances. The adhesion can be improved in many cases by pretreatment of the substrates with a primer. If adhesion difficulties arise please contact our technical service. Processing The substrate areas that will be in contact with the seal - ant must be clean, dry and free of all loose material, dust, dirt, rust, oil, and other contaminants. Non-porous substrates should be cleaned with a solvent and a clean, lint-free, cotton cloth. Remove residual solvent before it evaporates with a fresh clean, dry cloth. Storage The ‘Best use before end’ date of each batch is shown on the product label. Storage beyond the date specified on the label does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intend - ed use must be checked for quality assurance reasons. Safety notes During vulcanization acetic acid is released. These vapors should not be inhaled for long periods or in high concentration. Hence, good ventilation of the work place is necessary. Should uncured silicone rubber come into contact with eyes or mucous membranes, the affected area must be rinsed thoroughly with water as irritation will otherwise be caused. Cured silicone rubber, how - ever, can be handled without any risk to health.

60. 57 windscreen adhesive "ultimate" windscreen a dhesive Season-independent, high-modulus, non-conductive 1Kwindscreen adhesive. ► Season-independent. Your advantage: • 1hr. drive-away time with an airbag at an ambient temperature of –10°Cto+35°C. ► High-modulus. Your advantage: • Vehicle-strengthening windscreen adhesive. ► Suitable for antennas, non-conductive. ► Prevents contact corrosion. Your advantage: • Suitable for use on aluminum, magnesium and hybrid vehicle bodies (e.g. Audi A8, Jaguar XJ etc.). ► Tested safety. Your advantage: • Drive-away time confirmed via crash testing and TÜV certificate pursuant to FMVSS212/212! Meets requirements of original equipment manufacturers (motor- • vehicle manufacturers) Areas of application: Replacement glazing of cars and small transport vehicles. Use: A clean environment is to be selected for application. Use of the product with the accompanying Würth system components is essential for prop - erly performed and problem-free work. The work instructions accompany - ing the product are to be followed when carrying out work. Note: It is imperative that the Würth Active Cleaner and the Würth Varioprimer be used when preparing surfaces. The products are to be checked to ensure that they havenot expired before they are used. Apply adhesive while guiding the gun vertically, starting from the center at the bottom of the windscreen. Do not place the vehicle onthe lifting platform. Observe the information provided by the vehicle manufacturer in regard to bead geometry. The application and drive-away times must be observed. Designation Contents Art. No. P.Qty. Complete Set * 0890 023 800 1 Cartridge 310 mL 0890 023 801 1/12 Cartridge 150 mL 0890 023 811 1/24 Professional Set ** 0890 023 830 1 Bag 400 mL 0890 023 831 15 * Set = cartridge, Active Cleaner (double cloth), Varioprimer safe + easy (20 mL), priming brush, window application nozzle, repair instructions. **Set = bag, Active Cleaner (double cloth), Varioprimer safe + easy (20 mL), priming brush, window application nozzle, repair instructions. This information is only a recommendation based on our experience. Preliminary testing required! For further information see the technical information leaflet. Basic information ULTIMATE Chemical basis 1K polyurethane (moisture - hardening) Color black Application temperature +5°C to +35°C Processing time 15 min.* Storage temperature +5°C to +25°C Drive-away time w/o airbag 30 min.** Drive-away time w/airbag 1hr.** * measured at 23°C/50% rel. humidity. ** at an ambient temperature of –10°C to +35°C Additional article Active Cleaner, 500 mL Art. No. 0890 0241 Varioprimer, stick, 10 mL Art. No. 0890 024 010 Varioprimer, bottle, 20 mL Art. No. 0890 024 021 Varioprimer, bottle,100 mL Art. No. 0890 024101 !

62. 59 windscreen adhesive Description Contents ml Art No.: Pack/ Qty. Glass Sealant 310ml 0890 100 043 1/12 Description Contents ml Art No.: Pack/ Qty. Special Adhesive Plastic bag 1g, activator ampoule 0.5ml 0893 40 1 adhesive trim tape 1K windscreen adhesive for utility vehicles, buses and vehicles on rails. ► 600 mL bag contents. Your advantage: Designed for adhering large windscreens. • ► Normal-modulus. Your advantage: Elastic, tolerance-compensating windscreen adhesive. • ► Long processing time. Your advantage: User-friendly application. • ► Excellent stability. Your advantage: Very easy to use on vertical adhesion surfaces, e.g. side • windows . ► Smoothes easily. Your advantage: Very highly suitable for visible joints. • ► Environmentally-friendly: comes in a bag. Your advantage: More product, less packaging space,reduces garbage. • Areas of application: Replacement glazing of utility vehicles, omnibuses, transport vehicles, agricultural machines, construction machines and vehicles on rails. Use: A clean environment is to be selected for application. Use of the product with the accompanying Würth system components is essential for properly performed and problem-free work. The work instructions accompanying the product are to be followed when carrying out work. Note: It is imperative that the Würth Active Cleaner and the Würth Varioprimer be used when preparing surfaces. The products are to be checked to ensure that they have not expired before they are used. Apply adhesive while guiding the gun vertically, starting from the center at the bottom of the windscreen. Do not place the vehicle on the lifting platform. Observe the information provided by the vehicle manufacturer in regard to bead geometry. The application and drive-away times must be observed. Article Contents Art. No. P.Qty. Bag 600 mL 0890 023 600 12 Basic information ULTIMATE Chemical basis 1K polyurethane (moisture - hardening) Color black Application temperature +10°C to +40°C Processing time max 15 min.* Storage temperature +5°C to +25°C Drive-away time w/o airbag 3 hr.* Drive-away time w/airbag 16 hr.* * measured at 23°C/50% rel. humidity. This information is only a recommendation based on our experience. Preliminary testing required! For further information see the technical information leaflet. Active Cleaner, 500 mL Art. No. 0890 0241 Varioprimer, bottle,100 mL Art. No. 0890 024101 !

68. 65 thread lock & pipe sealant dos system Revolutionary one-handed dosing system ► Well-laid-out and orderly storage through the use of storage rack. Your advantage: No time-consuming searching. Quick • overview of available materials. ► Storage rack makes overhead bottle storage possible. Your advantage: Medium is always available for use • right away without shaking or squeez - ing. ► Room for 14 bottles. Your advantage: Especially common products can • bestocked in duplicate. ► Practical one-handed use thanks to the clever turn lock. Your advantage: You’ll always have a free hand! • ► Dosing head with self-cleaning closure system. Your advantage: No residual material in dosing spout! • ► Continuously adjustable dosing system. Your advantage: Application-tailored consumption-and - • cost-minimized dosing! ► Bellows-type bottle for high-viscosity materials. Your advantage: Cost optimization through almost com - • plete emptying of container contents! ► Silicone-free. Your advantage: Can be used without hesitation in the • automotive industry! Art No.: Description P. 0891 273 Retainer for DOS system, three compartm. 1 0891 271 Retainer for DOS system, seven compartm. 0891 273 14 Retainer for DOS system,14 compartm. Wall mount

28. 25 panel adhesive m irror a dhesive Solvent-free. Art. No. 890.600 Colour: Bright grey Contents: 290 ml Pack/Qty.: 1 Bonding of silver mirrors according to DIN 1238. (We recommend for other • mirrors examining, whether the mirror coating is attacked by the adhesive.) Bonding of plastic mirrors. • Bonding of sheet glass. • Odour-free and water proofed. • Plastic. • Ageing consistent. • Converting Surface: Wall or blankets have to be clean, dry and dust-free or free of grease. • Remove lacquer layers or loose stucco. • The mirror may not be stuck on a wet or damp surface. • Junction: Assemble mirror after the application of the adhesive within 5 to 10 • minutes, press on firmly. Fastening: Mirrors of 2 and 4 mm of strength can be stuck straight away to • vertical walls only with the mirror adhesive. Apply the mirror adhesive in vertical stripes. • Crawler strength between 6 to 8 mm. The distance between the stripes should • be 10 cm. Big, vertical mirrors (strength from 6 to 8 mm) and mirrors on angular walls or • blankets have to be fastened in addition mechanically. Fixing: Big mirrors should be fixed approx. 12 hours. • Aeration: The back of the mirror has to be left aerated so that the adhesive can • connect up. Areas of application Mirrors on walls and doors. • Mirror walls in shops, offices, restaurants and night clubs. • On walls of sustainable on-wall and concrete. • Wood, gypsum carton plates and flake boards. • Styrofoam. • Information Consumption: Approx. 1 cartridge per m • 2 at a crawler application strength of 6-8 mm. Cleaning: With LU-cleaner, Art. No. 890.108 in fluid condition. • Removing only mechanically in cured condition. • Raw material base: Polymeric rubber Specific weight: 1.4 g/cm 3 Open time: Approx. 15 min. at 20°C / 50% of relative humidity Full hardening: 1.5 mm/24 hours Converting temperature: +5°C to +30°C Temperature stability: +100°C Volume change: < 5% Shore-A-hardness: Approx. 30 Tensile Strength: 0.8 N/mm 2 Shelf life: 12 months at +5°C - +30°C Technical data

18. 15 s ilicone Advanced silicone with food safe anti fungal compound. Art. No. 892.555 Colour: White Pack/Qty.: 1 For refrigeration and food preparation areas. • Forms a permanently flexible, hygienic seal. • Sticks best to metals, most plastics, ceramics and glass. • For interior use. • Shelf life: 12 months. • Description High modulus acetic cure fungicidal silicone sealant and adhesive designed specifically for sealing refrigeration units and areas where repeated food contact is likely. Advantages Mould resistant - will not taint food. • Safe for repeated food contact. • Meets the US Federal Food & Drug Administration (FDA) Regulations. • Contains fungicide - highly resistant to mildew and mould growth. • Fast cure (tack free in one hour). • Movement accommodation of +/- 25%. • Excellent adhesion to most non-porous surfaces. • Temperature resistant to 150°C. • Areas of use For sealing in refrigeration units. • Sealing worktops/ kitchens (domestic and industrial) where food contact • is likely. Seals ceramics, porcelain, vitreous enamel, glass, metals and most • plastics/plastic coated metals. Application All surfaces to be sealed must be sound, dry and clean. • Cut the tip of the cartridge taking care not to damage the thread. • Apply nozzle and cut cleanly at an angle of 45 degrees with an • opening slightly larger than the gap to be sealed. Apply using a standard sealant gun. Best results will be obtained by • keeping an even pressure on the gun trigger and keeping the gun at a constant angle to the surfaces to be sealed. To ensure a proper bond, always smooth down sealant using a spatula • or piece of wood wetted with soap and water solution. Tool down within 15 minutes of application. • An improved appearance can be achieved by placing masking tape to • both sides of the joint, removing within 5 minutes of application. Note: Do not use on porous surfaces (such as brick, concrete and stone), on soft metals (such as lead), on surfaces that bleed oils or plastics and do not use externally (susceptible to UV radiation). foodmate silicone

79. 76 a dhesive tapes adhesive mirror tape Double-sided adhesive tape with polyethylene carrier and acrylate adhesive. ► Very good compatibility with all known surfaces. Your advantage: The adhesive tape is suited for adhesion to many different materials, suchas wood, metal, glass, stone, Plexiglas,and Macrolon (no formation of tension cracks). ► High initial stickiness. Your advantage: Directly after assembly, a sufficient application safety is achieved (optimum final hardness after 24 hours). ► UV and moisture-resistant. Your advantages: The adhesive tape can be used both indoors and outdoors. The adhesive force is not impaired by the humidity in sanitary areas. ► Good fit. Your advantage: The tape fits slightly uneven surfaces very well (the unevenness, however, may not be stronger than the tape itself). ► Resistant to ageing. Your advantage: In case of proper use, the tape does not lose its elasticity and permits adhesion over many years. Notes on application The surfaces to be glued must be dry and dust, grease, and • silicone free. To ensure proper adhesion, the tape must be sufficiently • pressed onto the material to be glued. Optimum final strength is achieved after24 hours. • With critical surfaces (e.g. PP, PE, rubber) and porous founda - • tions (e.g. wood, stone), please carry out preliminary tests. In cases where plastics containing softener additives are to be • adhered, the softener can modify the adhesive coating.This impairs the strength of the adhesive. In case of safety mirrors (recognisable by a blue or green foil • on the back sideof the mirror), mirror manufacturers generally recommend an additional mechanical fastening. Please observe the mounting instructions on the back! Colour width in mm Length in m Thickn. in mm Art. No. P.Qty. White 19 25 1 0894 918 0 1 25 0894 918 Black 12 1.6 0894 919 Applications Mounting of mirror. • Attachment of window bars. • Attachment of dispensers and mounts in sanitary areas. • Attachment of hooks • Technical data Art. No. 0894918 0 / 0894 918 Art. No. 0894 919 Adhesive basis Acrylate adhesive Carrier Polyethylene foam Bonding strength 23 N / 25 mm 16 N / 25 mm Elongation at tear >150% Application temperature +5°C to +40°C (applies to the surface and the adhesive tape) Thermal stability –40°C to +95°C Shelf life (at approx. +20°C and 50% humidity) 24 months UV resistance given Moisture resistance given

24. 21 panel adhesive Description Contents ml Art No.: Pack/ Qty. Cartridge 380 892.151 1 solvent free B uilding adhesive Environmentally friendly. • Low odour. • High bond strength. • “Trade size” 380 ml cartridge. • Quick drying. • Suitable for interior and exterior use. • Over-paintable. • Sandable. • Non-flammable. • Description: Solvent free building adhesive is a low odour general-purpose high bond strength adhesive using unique polymer technology eliminating the need for solvents. Quick drying but with ample open time for positioning, sandable and over-paintable, adheres to virtually any building and construction materials including polystyrene. For interior and exterior use, rough, smooth, vertical or horizontal surfaces. Non-flammable. Re-sealable nozzle. Application Fixing skirting boards, architraves and dado rails. • Bonding timber frames to brick and stone. • Fixing wall panels to battens. • Bonding floor grippers and metal edges (on porous surfaces). • Wood to wood bonding. • Bedding and bonding worktops to units. • Fixing loose roof tiles and slates. • Laying carpet and carpet tiles. • Bedding and bonding windowsills. • Fixing plasterboard panels partitioning. • General DIY and repairs. • Fixing polystyrene and architraves. • Limitations Solvent free building adhesive should not be applied in permanently damp or wet areas. Technical data Base: advanced polymer. Solids: 80 +/- 2%. Viscosity: viscous paste. Colour: beige Tack time: 10 - 15 minutes. Coverage: 11m per cartridge with 6 mm bead. Flash point: N/a Shelf life: 12 months when stored between 4°C and 25°C. Description Contents ml Art No.: Pack/ Qty. Cartridge 380 1892.100.380 1

46. 43 w ood g lue Especially formulated for all wood bonding where a fast set, high bond • strength and excellent water resistance are required. Suitable for use with virtually all woods, wood decoratives and high-pressure decorative • laminates. Extended opening time. • Modified mix provides higher performance with pine. • Additive is only effective • for 24 hours. One part modified polyvinyl alcohol stabilised vinyl acetate homopolymer • emulsion, containing coalescing solvent. May be used with hot or cold presses. • May be cured by radio frequency bonding. • Conforms to the wear resistance requirements of DIN 68602 to Category B. • Conforms to BS 4071 in respect of bond strength resistance to sustained load and freeze • thaw stability. Typical properties Type: Reactive PVA Emulsion Colour: White (clear when dry) Viscosity: 9500 cps (Brookfield viscometer spindle 6, 20 rpm) Ph: 4 Minimum film forming temperature: 2°C Solids content: 4.7% Specific gravity: 1.10 Application Bonding conditions: The adhesive substrates and ambient temperature should ideally be at a minimum 20°C (68°C). The moisture content of wood materials should be uniform and not exceed 12%. Spreading: The adhesive can be applied by serrated glue spreader roller or brush. Application is normally to one surface at a rate of 150 gm/m≤ (0.5 ozs / sq. ft). Maximum 30 minutes depending on materials to be bonded. Assembly times should be minimised at low wood moisture. Pressing: Pressure must be applied whilst the adhesive is still wet and should be a minimum of 30 psi (2kg/cm≤) depending on type of wood and structure. Press times: Press times required, depend on adhesive coating and upon substrates. Typical figures are Hot press Cold press Decorative laminate/ 50°C - 8 mins 20°C - 20 mins plywood or chipboard 60°C - 5 mins - Packaging: Do not allow to freeze. Storage life not more than 6 months is recommended. Cleaning: Equipment should be cleaned with warm or cold water while the adhesive is still wet. Contents Art No.: Pack/Qty. 500g 892.100.16 1 1 kilo 892.100.17 5 kilo 1892.100.13 12 kilo 892.100.14 25 kilo 892.100.15 45 gallons 999.250 Brush for wood glue 2 1 892.100.010 Empty glue bottle 500ml with nozzle 2 892.100.0 1 Bottle/4 Nozzles Note: Contact with ferrous metals i.e. steel, or iron can cause the glue to turn blue or black. Avoid contact with steel clamps . pva woodglue

64. 61 e poxy resin a dhesive Temperature in °C Hardening time in min 10 approx. 120 15 approx. 70 23 approx. 60 40 approx. 25 60 approx. 10 100 approx. 2 power B ond High-strength two-component epoxy resin system for repairs to motor-vehicle bodies ► High-strength epoxy resin adhesive. Your advantages: The repair restores the original strength and • stiffness. Fewer spot welds. • Meets the requirements of motor vehicle • manufacturers. • ► Glass-particle technology Your advantage: Even if strong pressure is exerted, an adhesive • thickness of 0.7 to 1.2 mm remains. ► Excellent stability. Your advantage: The adhesive will not run on vertical surfaces • (thixotropic). ► Excellent corrosion protection. Your advantages: The original rust resistance is maintained. • Corrosion is prevented at welds. • ► Can be through-welded ► Can be ground and painted over ► Free of silicone Note: Not suited for load-bearing vehicle body parts (e. g. A-pillar, frame side bar). If body parts are only partially replaced, do not glue on visible surfaces since shadow seams may appear. Observe the vehicle manufacturer’s repair instructions. Technical data: Application: Structural adhesive for steel, aluminum and fiber-reinforced plas-tics (FRP, CFRP). For gluing motor-vehicle body parts such as side-walls, wheel arches, roof and door plates. Acetone Cleaner, Art. No. 0893 460 Rust-Stop Quattro, Art. No. 0893 214 1 Pneumatic Sanding Machine, Art. No. 0703 231 0 Flexi-Disk, Art. No. 0578 705... Nylon Fleece Disk, Art. No. 0673 22 50/75 Mini Fleece Disk, Art. No. 0673 205.../207 ... Vice-Grip Pliers, Art. No. 0714 09... ! This information is only a recommendation based on our experience. Preliminary testing required. *measured at 23°C Chemical basis Epoxy resin Color black Density 1.1 g/cm 3 Application temperature +15°C to +25°C Application time 60 min.* Hardening time 4 hr.* Final strength after 72 hr.* Shore D hardness (DIN 53505) 80 Tensile strength (ASTM D-638) 30 MPa* Tensile shear strength (EN 1465) 1.7 MPa (after 4 hr.)* 13.3 MPa (after 8 hr.)* 19.0 MPa (after 17 hr.)* Resistant to Fuels (petrol, Diesel oil), motor and transmission oil, coolant. Thermal stability –30°C to +120°C (for short peaks up to +190°C) Durability 12 months Designation Cont. Art. No. P. Qty. Powerbond Motor-Vehicle Body Adhesive Set * 0893 964 450 1 Powerbond Motor-Vehicle Body Adhesive 225 0893 450 100 1/6 Positive mixer 0891 450 101 15 Application gun 0891 450 100 1 * Set = 2 cartons motor-vehicle body adhesive, 15 positive mixers, 1 application gun, 1 acetone cleaner, 1 Rust-Stop Quattro, 1 repair instruction.

63. 60 e poxy resin a dhesive epoxy resin fast-acting adhesive esk-48 Solvent-free two-component adhesive. ► Fast curing. Your advantage: The reaction of the two components results in a fast setting • speed. And that ensures fast application. ► Broad range of applications. Your advantage: For bonding metals, many plastics,glass, ceramic etc. to each • other. ► High tensile strength values. Your advantage: Tensile shear strengths are retained even under influence of • heat. ► Outstanding resistance to chemicals. Your advantage: Resistant to many liquids, such as petrol, many lubricating oils • and ethyl acetate. Other advantages Can be sanded when fully hardened. • Viscoelastic. • High transparency. • Notes on application: The static mixing tube is attached to the double cartridge of the ESK-48 and the cartridge is laid in the gun.The bonded joint must be uniformly pressed until final strength is achieved. The best adhesive bonding strengths are achieved after cleaning and lightly sanding with a maximum bonding gap of 0.1mm. The curing time is dependent on the temperature. Adhesive not completely cured can be removed with Acetone Cleaner, Art. No. 0893460. The reaction can be accelerated by applying heat of +80°C. If work is interrupted for longer than 3 minutes, change the positive mixer. Application: Adhesive bonding of stainless-steel sheets to each other, • repairs of broken-off plastic and metal parts, manufacturing of PCBs etc. Hardening speed for tensile shear strengths of >10N/mm 2 : Basis Epoxy resin Colour Clear, transparent Density Binder: 1,14 g/cm 3 Hardener: 1,15 g/cm 3 Viscosity Binder: 20–60 Pa·s Hardener: 25–65 Pa·s Processing time 4 min at +23°C Final strength 1 hr Tensile shear strength 7 N/mm2at +23°C Ideal application temperature +23°C Thermal stability –60°C to +80°C Handling strength After approx. 5 min Shelf life 12 month sat +15°C to +20°C Technical data: Adhesive ESK-48 Designation/ Container Cont. in ml Art. No. P. Qty. Double cartridge 48 0893 480 3 Positive Mixer for ESK-48 Art. No. P. Qty. 0891 481 3 Gun for ESK-48 Art. No. P. Qty. 0891893 485 1 Acetone Cleaner Contents in ml Art. No. P. Qty. 250 0893 460 1 Temperature in °C Hardening time in min 10 approx. 120 15 approx. 70 23 approx. 60 40 approx. 25 60 approx. 10 100 approx. 2 With this information we want to advise you to the best of our knowledge based on our tests and experience. How - ever, we shall assume no liability for the application results in individual cases due to the large number of applications and the storage and application conditions which lie outside the scope of our influence. This also applies to the use of the non-binding technical and commercial Customer Service we provide. We always recommend that you conduct your own tests. We guarantee the consistent quality of our products. We reserve the right to make technical changes and carry out further development.

82. 79 a dhesive tapes adhesive trim tape High-strength double-sided adhesive tape with polyethylene carrier and acrylate adhesive. ► Very strong adhesion. Your advantages: The tape provides outstanding adhesion imme - • diately after installation of the trim. A high level offinal adhesive strength is achieved after a curing time of 24 hours. Very strong adhesion also onrough and slight - • ly uneven surfaces. ► Foam carrier. Your advantage: The tape has a vibration-damping effect and • compensates for the expansion properties of two different materials. ► High temperature, UV and weather resistance. Your advantages: The tape can be used indoors as well as • outdoors. Does not lose adhesion at higher • temperatures. Instructions for use The surfaces to be joined must bedry and free • from dust, grease and silicon. In order to assure perfect adhesion, sufficient • pressure must be applied to the tape during installation. Optimal final adhesive strength is reached • after 24 hours. In case of sensitive surface finishes (e.g. PP, • PE, rubber) and porous surfaces (e.g. wood or stone), carry out a preliminary application test. In case of plastic materials to be joined con - • taining plasticizer additives, these additives may change the adhesive layer and impair the strength of the adhesive (perform preliminary test). Areas of application: Trim and functional metal strips, logos, emblems, screens and • holding brackets in the automobile industry. Attachment of name plates on machines. • For attachment of spoilers in connection with mechanical • elements. Width mm Length m Thickness mm Art. No. P.Qty. 4 10 0.8 0894 910 4 1 12 0894 910 19 0894 910 0 24 0894 910 1 These notes are intended to provide our advice to the best of our knowledge, based on tests and experience. How -ever, we cannot assume any liability for processing results in individual cases due to the wide variety of applicationsas well as storage and processing conditions beyond ourcontrol. This also applies in case our technical and com-mercial customer service is consulted free of charge and without obligation. We recommend carrying out in - dividualtests. We guarantee the constant quality of our products.We reserve the right to make technical modifications and advanced developments. Adhesive base acrylate adhesive Carrier Polyethylene (anthracite) Adhesive strength 19N / 25 mm Elongation at rupture > 300% Application temperature +5°C to +40°C (applies to surface and adhesive tape) Temperature stability –40°C to +95°C Shelf life (at approx. +20°C and 50% humidity) 12 months UV resistance yes Moisture resistance yes Specifications:

92. 89 putty repair sticks p utty r epair s ticks Contents g Description Art. No. P. Qty. 180 Steel 1993 01 1 Plastic 1993 02 Aluminium 1993 03 an epoxy based hand malleable putty with the hardener forming the core of the stick When mixed the product rapidly • hardens ensuring rapid repairs to many different components and materials. When fully cured the material can • be drilled, tapped, filed, sanded or overpainted. Simple to use putty formulation en - • sures no runs or drips of product. Adheres even in the presence of • liquids e.g. underwater. Resin Epoxide Chemical Resistance Hydrocarbons, ketones, alcohols, esters, salt solutions, dilute acids, petrol diesel and oils Electric Resistance 30.000Ω Dielectric Strength 300V/mm Shrinkage less than1% Non Volatile Content 100% Compressive Strength 12.000psi Maximum Temperature Resistance 120°C continuous 150°C temporarily Initial Cure maximum 1 hour Full Cure maximum 24 hours Shore Hardness D 80 after 24 hours Working Time 3.5 minutes Technical Data Steel Epoxy Stick Plastic Epoxy Stick Aluminium Epoxy Stick Cylinderblocks • Heads • Castings • Damaged threads • Worn Shafts • Water Pipes • All steel components • Bumpers • Dash board components • Fibreglass • Washer bottles • Baths • Swimming pools • Pipes • All plastic components • Radiators • All aluminium components • Application Areas This information is intended as a recommendation only, based on our experience. Preliminary tests to verify material compatibility should becarried out. The cleaning and care instructions of the manufac - turer must be observed!

49. 46 w ood g lue ever B uild resintate Product Description EVERBUILD RESINTITE is concentrated powdered wood glue based on urea-formaldehyde resins. RESINTITE is easily mixed with water and once dry, forms a bond stronger than the wood itself. RESINTITE may be used for cabinet making, general joinery, veneering, boat building and shop fitting applications. RESINTITE may be used internally or externally and is water resistant to BS EN204 D3 (test methods BSEN205 1991) and also conforms to BS EN301 1992 A3 (test method BSEN 302-1 1992) ie suitable for load bearing applications.. Benefits Excellent rate of bond strength development. • High degree of water resistance. D3 Clas - • sification- joints may be subject to short term water contact or exposure to high humidity. Interior/exterior use. • Low timber-staining characteristics - will not • stain. Suitable for load bearing applications – inter - • nally or externally. Makes 50% more than the pack contents once • mixed with water Gap filling ability • Areas For Use As a water resistant/load bearing wood ad - • hesive, internally and externally, specifically; cabinet making, general joinery, veneering, boat building and shop fitting Shelf Life 12 months when stored as directed above. • Storage Store in dry conditions between 5 and 25`C • in original unopened containers. Application Wear gloves to avoid contact of powder or mixed glue • with skin (dermatitis risk in sensitive persons). Avoid inhalation of dust. Mix with clean water prior to use. Mixing may be either • by weight or volume, using the following ratios. By weight; (recommended method for accuracy); Mix 2 • parts powder with 1 part cold water. By volume; Mix 3.5 measures of powder to 1 measure • of water. For both methods, use the following mixing procedure. • 1. Put half the water into a non metallic bowl • 2. Add all the powder and stir until dissolved. • 3. Add the remaining water and stir until smooth. • The mix is now ready to use and will remain usable for • approximately 3 hours at 15 `C. Apply to one surface only using a stiff brush. Assemble • and clamp (pin or screw) the joint whilst the glue is wet. Keep the joint under pressure until the glue is set (ap - prox. 6 hours at 15`C or longer at lower temperatures). Remove excess adhesive with a damp cloth before glue • sets. Surface Preparation All surfaces must be clean, dry and free from grease. • Colour Article No.: Pack Size Qty White 98921 700 1 3Kg 1 White 98921 900 1 25Kg Bag 1

54. 51 s uper g lue skg – instant adhesive gel Cyanoacrylate adhesive gel ► Stable setting Your advantage: Gel nature prevents running to the greatest degree. • ► Fast setting Your advantage: The adhesive hardens extremely quickly. • ► For universal use Your advantage: Adheres both smooth and absorbent surfaces. • ► Clean workability Your advantage: Quick and easy opening of the cap makes working easier. • Caution: It is advisable to wear safety gloves and goggles. Use: The parts to be bonded must be clean, grease-free and dry. Apply a thin, even layer of adhesive to just one of the sur-faces to be bonded. Produce the connection immediately with sufficient pressure to ensure complete contact. Maintain pressure during the time required for the fixation strength. Application surfaces: Metal, cork, felt, leather, rubber, porcelain, plastics (e.g. unplasti - cized PVC, ABS, polystyrene) with and among each another. Application: Bonding profile rubber for wooden and plastic windows • Sign attachments • Adhering of rubber seals • Repair of broken edges • Nitrile Disposable Glove Art. No. 089947003 Comfort Assembly Glove Art. No. 08994006.. Polycarbonate Goggles Art. No. 08991020 ! Basis Ethyl cyanoacrylate Color transparent Hardening system with humidity Viscosity gel, thixotropic Density 1.08 g/cm 3 deal application temperature +20°C Temperature resistance –30°C to +80°C Softening point +165°C Setting speed 20– 100 sec. (depending on material) Final strength after 24 hours Tensile strength 20 – 30 N/mm 2 according to DIN 53288 Tensile shear strength 25.5 N/mm 2 according to DIN 53283 Gluing gap size ideal 0.05 mm, maximum 0.25 mm Shelf life 12 months (cool and dry) With this information we want to advise you to the best ofour knowledge based on our tests and experience. How-ever, we shall assume no liability for the application resultsin individual cases caused by large numbers of applicationsand the storage and application conditions which lie outsidethe scope of our influence. This also applies to the use of thenon-binding technical and commercial Cus - tomer Service weprovide. We always recommend that you conduct your owntests. We guarantee the consistent quality of our products.We reserve the right to make technical changes and carryout further development. Contents in ml Art. No. P. Qty. 3 g 0893 403 1/40 20 g 0893 403 1 1/10 Technical data: PRIMER Adhesion promoter • for pre-treatment of PE, PP, PTFE and silicone rubber. Fast-acting. • Caution: For combination bonding with different materials, only the non-polar surface may be primed! ACTIVATOR For accelerating the • reaction of Würth cyano-acrylate adhesives. The activator can be • usedon all surfaces. The activator is highly compatible with common plastics. However, when using for the first time, it should be tested in a non-visible location to determine whether theplastic is resistant to the activatoras a precautionary measure. Content Art. No. P. Qty. 35 ml 0893 091 0 1 Content Art. No. P. Qty. 150 ml 0893 301 20 1/4

36. 33 pu sealer B ond & s eal fast Fast-acting, brushable PU sealant. ► Highly adhesive, permanently elastic sealing compound. Your advantages: Very good adhesion to bare, primed and • painted sheet metals. Compensates for tolerances/bridges gaps. • Permanent, reliable seals. • ► High degree of stability. Your advantages: Excellent smoothing properties. • Can be applied with a spatula or brush. • Can be textured with a brush or smoothing • tool. ► Short skin formation time. Your advantages: The sealant surface is non-adhesive after a • short time. ► Can be painted over quickly. Your advantages: Can be painted over quickly thanks to the • short skin formation time (check paint compat - ibility via preliminary testing!). ► Approved for use with foodstuffs (ISEGA certificate). Your advantages: Harmless to humans in hardened state. • Suitable for sealing in food-processing plants. • ► Non-corrosive. Your advantages: Prevents metal corrosion. • ► Nearly odorless. ► Silicone-free. Technical data: Chemical basis 1-component polyurethane Application temperature +5°C to +35°C Skin formation time* approx. 20 min. Curing speed *3 mm/24 h (moisture-hardening) Volume change (DIN 52451) –6% Shore A hardness (DIN 53505) approx. 40 Thermal stability Briefly up to –40°C to +90°C 8h at +120°C Resistant to water, seawater and limy water, public waste water, weak acids and alkaline solutions. Briefly resistant to fuels, mineral oils, vegetable and animal fats and oils. Areas of application: For permanently elastic, highly adhesive sealing of overlapping seams, spot- welded seams, visible joints, sheet-metal connection joints and folded seams, both indoors andout. Use: The application surfaces must be clean,dry and dust- and grease-free (see Bond+Seal surface optimization). Material not hardened can be removed with B+S Remover, Art. No. 0890100 63, while hardened material can only be re-moved mechanically. Note: Do not bring into contact with alkyd-resin paint systems. Not suitable for glass groove sealing in areas in which UV back reflection can occur. Direct expo - sure to sunlight can lead to slight surface yellowing. Not suitable for PE, PP, PTFE, silicone rubber, expanded polystyrene and softe-ned plastics. Please remind to keep a minimum adhesivethickness of 3 mm for a secure bonding.To achieve an optimal adhesion the use of Würth B+S Primer products is essential ! Attention should be paid to critical application surfaces like non-ferrous metals(copper) and galvanized materials.For smoothing you can use Würth Sealant Smoothing Agent. Color Contents ml Art. No. P. Qty. white 300 0890 100 710 1/12/24 gray 300 0890 100 720 1/12/24 black 300 0890 100 730 1/12/24 Bond+Seal Activ. Cleaner Art. No. 0890100 60 Bond+Seal Primer for Metal Art. No. 0890100 61 Bond+Seal Remover Art. No. 0890100 63 Bond+Seal Primer for plastic/ wood/stone Art. No. 0890100 62 Sealant Smoothing Agent Art. No. 0893 3 Flat Nylon Brush Art. No. 0693 30 ! This information is only a recommendation based on our experience. When working with the product, the B+S optimization table must be followed. Preliminary testing required. For further information see the techni - cal information leaflet. *measured at 23°C/50% rel. humidity

84. 81 a dhesive tapes c ar Body s ealing t ape/ c ar Body r ound s ealing s trip Permanently plastic, self-adhe - sive sealing tape or round strip for sealing of overlapping car bodypanels. ► Very good adhesive properties. Your advantage: The tape offers very good adhesion as well as permanent • bonding on various different surfaces, e.g. metal, plastic, wood, stone, etc.(see processing notes). ► Good UV, weather and water resistance. Your advantage: Also suitable for outdoor use, resistant to rainand other weath - • er influences (not for use in submerged condition). ► Resistant to ageing and high temperatures. Your advantage: Provided the tape is used expertly, adhesion and sealing is • assured over a number of years. Also suitable for high-temperature applications, for example, • sealing of car bodies. ► Steam diffusion layer. Your advantage: The sealing tape or round strip enable water-tight sealing and • prevent the penetration of moisture into the car body. Other features: Noise and vibration damping. • Self-fusing. • Free of solvents and silicone. • Immediately ready for use. • Designation C Width mm Thick mm Length, mm Art No Pack Qty Car body sealing tape grey 20 2 26 (4 x 6.5) 0890 100 030 1/4 Car body round sealing strip black 8 17,5 (7x 2.5) 0890 100 033 10 10 (5 x 2) 0890 100 032 Areas of application: Universal use for sealing of overlaps and screw connections in • the automotive industry, container and motor home construc - tion, for example: ‘between fender and body, at brake and rear lights (particularly round sealing strip), at trim parts and sunroofs. Also suitable for general sealing jobs to protect against dust, • moisture and vibrations in electrical, machinery and construc - tion applications as well as heating, ventilating and aircon - ditioning, for example, between screw-connected parts, in seams, joints, housings of all types and pipe lead-throughs. Instructions for use: The surfaces to be sealed must be • dry, stable and free from grease and dust. The application temperature must • not be below +5°C. Absorbent and porous surface must • be pretreated with Würth Butyl/ Bitumen Primer (Art. No. 0892 875). The car body sealing tape or round • sealing strip must be pressed down carefully against the surface. Press the sealing surfaces together firmly to achieve an effective seal. Butyl has a tendency towards “cold • flow” (flow property of the tape). Therefore, butyl products should always be attached mechanically, i.e. with screwing components togetheror use of a contact profile. Applying excessive pressure to the • profile will cause “squeezing out” of the sealing compound. Never compress Butyl products to their zero point (use washer as spacer) Specifications: Material base Butyl rubber Fire protection class B2 Application temperature –5°C to +40°C Temperature stability –30°C to +100°C Shelf life (at approx. +20°C and 50% humidity) 24 months (store dry, lying flat and dust-free) These notes are intended to provide our advice to the bestof our knowledge, based on tests and experience. However, we cannot assume any liability for processing results in individual cases due to the wide variety of applications aswell as storage and processing conditions beyond our control. This also applies in case our technical and commercial customer service is consulted free of charge and without obligation. We recommend carrying out individual tests. We guaran - tee the constant quality of our products. We reserve the right to make technical modifications and advanced developments. Additional products: Butyl/Bitumen Primer • Art. No. 0892 875

37. 34 pu sealer B ond & s eal po wer Heavy-duty, elastic hybrid construction adhesive. ► Excellent adhesive range. Your advantage: Very good adhesion to almost all surfaces, • e.g. metals, steel, stainless steel, galvanized steel, aluminum, plastics (e.g. ABS, FRP, hard PVC) orceramic materials. ► Minimally elastic. ► High initial strength. Your advantage: No complicated attachment of components. • ► Suitable for painting over. Your advantage: Can be painted over before and after skin • formation with all conventional paint systems (except alkyd resin paints). ► UV-resistant. Your advantage: Very highly suitable for visible joints. • ► Non-corrosive. Your advantage: Prevents metal corrosion. ► Nearly odorless. ► VOC- and solvent-free. ► Isocyanate-, PVC- and silicone-free. ► Safety product. Your advantages: Especially user-friendly and safe handling. • Improved workplace safety and health • protection . ► NSF (P1)-registered (No.136996) . Your advantages: International approval for use in areas where • food is processed or stored. Very broad range of applications. • Technical data: Chemical basis 1-component polyurethane Application temperature +5°C to +35°C Skin formation time* approx. 40 min. Curing speed *3 mm/24 h (moisture-hardening) Volume change (DIN 52451) <2% Shore A hardness (DIN 53505) approx. 50 Thermal stability Briefly up to –40°C to +90°C 16h at +120°C/4 hrs. at +140°C Resistant to fresh water and salt water, aqueous tenside solutions Briefly resistant to fuels, mineral oils, vegetable and animal fats and oils Areas of application: For dynamically loaded structural con - nections and seam and joint sealing in autobody, vehicle and caravan construc - tion, railway car and container construc - tion, metal and equipment construction, in air conditioning and ventilation duct construction, in the foodstuffs industry and many more. Application: The application surfaces must be clean, dry and dust and grease-free. Material not hardened can be re-moved with B+S Remover, Art. No.0890100 63. Hardened material can only be removed mechanically. Note: Do not bring into contact with synthetic- resin paint systems (alkydresin). Not suitable for PE, PP, PTFE, silicone rubber, polystyrene and softened plastics. Note that a minimum adhesive thickness of 3mm must be complied with to ensure secure adhesion. To achieve optimum adhesion results, the use of Würth B+S Primer products is essential! This is especially important with critical surfaces, such as non-ferrous metals (copper) and galvanized materials. Use Würth sealant smoothing agent for smoothing. Color Contents ml Art. No. P. Qty. white 300 0893 235 1 1/12 gray 300 0893 235 2 1/12 black 300 0893 235 3 1/12 Bond+Seal Activating Cleaner Art. No. 0890100 60 Bond+Seal Primer for Metal Art. No. 0890100 61 Bond+Seal Primer for plastic/ wood/stone Art. No. 0890100 62 Bond+Seal Remover Art. No. 0890100 63 ! This information is only a recommendation based on our experience. When working with the product, the B+S optimization table must be followed. Preliminary testing required! For further information see the technical information leaflet. *measured at 23°C/50% rel. humidity nsf ®

95. 92 tarp repair system tarp repair system Mobile, self-adhesive repair system for defective truck tarps, tents, covers and much more. Problem solution – Simple, long-last - ing and mobile Simple, professional repair. Ready-to-use patches with high bonding • strength. Fast application. • Large choice of colors. • Can be used on the go. Fast, reliable repair of damaged areas at • any time. Cost-optimized. No need to visit a workshop. • Repair times are considerably reduced. • Unnecessary down times are decreased. • No more recourse claims based on freight • damage. UV-resistant. Resistant to washing brushes. Areas of application: Unique system for the repair of defective tarps on the road and in the repair shop. Holes, rips and tears can be repaired permanently in an uncomplicated manner at low cost. Can be used for truck tarps, event tents, impact and piste guards as well as box bodies, campers, ski boxes and much more Note: Application temperature: –15°C to +40°C, Temperature-resistance: –40°C to +70°C Use: The surface must be clean, dry and grease-free. Clean dirt and oil over a large area from the defective spots with a clean cloth (TexRein, Art. No. 0899 810) and 1A Assem - bly and Part Cleaner Art. No. 0890 106 500. Select a patch and remove the protective film. Adhere the patch onto the surface without folds, press it firmly into place and hit it using a rubber mallet on a firm surface, if necessary. Attention! – The patch can - not be pulled off and corrected following application! Color Patch Kit 32pc.** Art. No. Patch Kit 500 x 210 mm*** Art. No. P. Qty. Silver 161 0880 600 161 0880 800 161 1 White 290 0880 600 290 0880 800 290 1 Ivory 1014 0880 601 014 1 Zinc yellow 1018 0880 601 018 0880 801 018 1 Broom yellow (DHL) 1032 0880 601 032 1 Pure orange 2004 0880 602 004 1 Deep orange 2011 0880 602 011 1 Fire red 3000 0880 603 000 0880 803 000 1 Ultramarine blue 5002 0880 605 002 0880 805 002 1 Light blue 5012 0880 605 012 0880 805 012 1 Emerald green 6001 0880 606 001 0880 806 001 1 Yellow green 6018 0880 606 018 1 Light gray 7035 0880 607 035 0880 807 035 1 Black 9005 0880 609 005 0880 809 005 1 *All colors are similar to RAL; 161 and 290 are manufacturer specifications./ **Contents: 3 300 x 200 mm patches, 3 200 x 200 mm patches, 4 300 x 100 mm patches, 4 200 x 100 mm patches, 6 100 x 100 mm patches, 6 200 x 50 mm patches, 6 100 x 50 mm patches./ ***Contents:10 plasters of size 500 x 210 m m. This information is only a recommendation based on our experience. Preliminary testing required! For further information, see the technical information lea fl et. Additional articles TexRein Cleaning Cloth Art. No. 0899 810 P. Qty. 1 1A Assembly and Part Cleaner, 500 mL Art. No. 0890 106 500P. Qty. 1 Rubber Mallet Art. No. 0715 734 08P. Qty. 1 !

78. 75 a dhesive tapes flexen ® accessories adhesive tapes Fig. Designation Barrier layer Width in mm Length in m Art. No. P. Qty. 1 Adhesive Tape, isogene gray – 30 20 0874 100 011 20/1 2 Adhesive Tape, red – 50 20 0874 100 040 20/1 3 Adhesive Tape, silver – 50 20 0874 100 050 20/1 4 Adhesive Tape, black – 50 20 0874 100 060 20/1 5 Fabric Adhesive Tape, silver – 50 50 0874 100 200 12/1 6 Pure Aluminum Adhesive Tape PE fi lm 50 50 0874 100 340 1 75 50 0874 100 341 100 50 0874 100 342 7 Pure Aluminum Adhesive Tape Paper 50 50 0874 100 320 1 75 50 0874 100 321 100 50 0874 100 322 8 Aluminum Adhesive Tape – 50 100 0874 100 330 1 75 100 0874 100 331 100 100 0874 100 332 wrapping tapes Fig. for Flexen ® Designation Width in mm Thickeness in mm Roll Length in m Art No.: P.Qty 1 Heating Rubber plus Rubber Wrapping Tape, gray, self-adhesive 50 3 15 0874 105 010 12/1 2 Rubber plus Rubber Wrapping Tape, black, self-adhesive 50 3 15 0874 105 020 12/1 3 PE PE Wrapping Tape, gray, self-adhesive 50 3 10 0874 105 030 12/1 4 Fleece Protective Hose Fleece Wrapping Tape, self-adhesive 70 2 5 0874 105 040 20 5 Fleece Wrapping Tape with fi lm 70 2 5 0874 105 041 20 6 Fleece Wrapping Tape, self-adhesive, with fi lm 70 2 5 0874 105 042 20 7 Fleece Protective Hose B2 Fleece B2 Wrapping Tape with fi lm 70 2 5 0874 105 070 20 8 Fleece B2 Wrapping Tape, self-adhesive, with fi lm 70 2 5 0874 105 071 20 9 PE Protective Hose PE Wrapping Tape, with fi lm on one side 70 2 5 0874 105 060 16 10 PE Wrapping Tape, self-adhesive, with fi lm on one side 70 2 5 0874 105 061 16 * Delivered with 16 rolls of 5 m in 8 double rolls of 2 x 5 m each. The P. Qty. and the price however refers to 1 roll of 5 m. ORSY • ® organisation Stable shelf for FLEXEN • ® pipe insulation Can be set up free-standing • Wall and fl oor mounting required. • Small base, yet large storage area as the shelf has four levels. • The shelf is accessible from all sides. • flexen ® shelf Art No.: 0961 870 P.Qty. 1

77. 74 thread lock & pipe sealant Notes: Material is applied to the parts directly in liquid form and then hardens into a toughened plastic after installation. It completely fills the gaps so that the resulting connection provides excellent protection against corrosion from fric - tion and protection against rust. A 100% seal is achieved. Applications: Automotive and utility vehicle industry, metal and tool manufacturing, ship building, machine and engine construction, electrical and electronics con - struction. Mandatory warning symbols: These products are free from mandatory warning symbols! Your advantage: They comply with Section 16, Paragraph 2of the German Hazardous Material Ordinance. (“The worker must check whether substances, prepara - tions or products with a lower health risk than those intended for use by him/her are available!”) Resistance Resistant to a large number of bases, gases, solvents, oils and fuels. Notes on application The material is applied in liquid form directly and evenly to the oil- • ,grease- and dust-free surface. The cleaner the surface, the more secure the connection. • These adhesives harden anaerobically, which means that they only • harden where no atmospheric oxygen contacts the adhesive. For this reason, the containers a real so only filled to approx. 3/4. • At the same time, the hardening speed is still being influenced by the • catalytic effect of metal and the gap width. The more “passive” the material and the thicker the gap, the slower the • material hardens. Passive materials: Nickel, zinc, tin, precious metals, aluminum with • minimal copper and/or manganese content, highly-alloyed steel, oxide orchromate coatings, plastic, glass and ceramic. Active materials: Steel, brass, bronze,copper, aluminum (copper con - • tentgreater than 1%). For cleaning and degreasing, were commend Brake Cleaner, Art. • No.089010871. Attention: The following plastics can be attacked in case of longer exposure: • ABS, celluloid, polystyrene, polycarbonate (Macrolon), PMMA (Plexiglas), polysulfone, SAN (lurane, Tyril),Vinidur, vulcan fiber and painted surfaces. We always recommend that you conduct your own tests. List of articles: Art No.: Description Contents P. 0893 243 025 Mid-Strength Screw Lock 25 g 1 0893 243 050 Mid-Strength Screw Lock 50 g 0893 243 250 Mid-Strength Screw Lock 250 g 0893 270 025 High-Strength Screw Lock 25 g 0893 270 050 High-Strength Screw Lock 50 g 0893 270 250 High-Strength Screw Lock 250 g 0893 603 025 High-Strength Bearing Lock 25 g 0893 603 050 High-Strength Bearing Lock 50 g 0893 603 250 High-Strength Bearing Lock 250 g 0893 620 050 Heat-Proof Fügefest (heat-resistant bearing lock) 50 g 0893 620 250 Heat-Proof Fügefest (heat-resistant bearing lock) 250 g 0893 573 050 Green Surface Sealant 50 g 0893 573 250 Green Surface Sealant 250 g 0893 574 050 Orange Surface Sealant 50 g 0893 574 250 Orange Surface Sealant 250 g 0893 518 050 Low-Viscosity Surface Lock 50 g 0893 518 250 Low-Viscosity Surface Lock 250 g 0893 577 050 Pipe Sealant 50 g 0893 511 050 Pipe Sealant with PTFE 50 g 0893 511 250 Pipe Sealant with PTFE 250 g 0893 545 050 Hydraulic Seal 50 g 0893 545 250 Hydraulic Seal 250 g 0893 260 100 Engine Seal 100 g

91. 88 liquid metal l iquid m etal f e1 Ideal, fast-acting repairsystem for install - ers and workshops in the metal-process - ing field. Especially suitable for filling shapes, sealing and spackling leaky spots. Fe1 is a high-quality two-component reaction resin system that • exhibits characteristics of metal due to its special formula. The ideal mixing ratio of the components (A:B = 1:1, pressing • outtwo strands of the same length from the tubes) makes faulty mixing of the repair mass almost impossible. Fe1 is specially designed for smaller repair jobs under pres - • sure of time. Fe1 can be applied with a spatula and does not run, which • makes vertical application possible as well. After hardening, Liquid Metal Fe1 can easily be processed via • lathing, milling, drilling, filing or thread cutting, just like with metal. Glass Fabric Ribbon For strengthening the metal mass when repairing with Liquid • Metal Fe1. Dimensions: 1,000 x 50 x 1.3 • Art. No. 0894 650P. Qty. 1 Processing instructions The metals must be cleaned and degreased bare. Mix components A and B homogeneously 1:1. Apply mixture immediately with a spatula (short pot life). The hardened liquid metal can be lathed, milled, drilled etc. Please note the accompanying application instructions. Contents in g Art. No. P. Qty. 500 0893 449 1 Abrasions on: Leak-sealing on: Blowholes in: Run-in damage on: Creation of: pump housings • impellers • propellers • rudders • heat exchangers • condensers • dust pipes • slides • chutes • bolts • torn-out threads • cooling units • tankscasting • water tanks • water pipes • oil pipes • housings • grey cast iron during casting • grey cast iron during processing • shafts • hydraulic cylinders • blocks • bearing seats • crankcases • shapes • retainers • models • guides • prototypes • Mixture ratio component A : component B = 1:1 Tack cure time 7–12 min. (at room temperature) Hardening time 4–24 h (at room temperature) Pot life 5 min./20g (at room temperature) Consistency does not run Spec. weight 2.80 (components A and B mixed) Compressive strength 70 N/mm 2 Tensile strength 12.5 N/mm 2 Shear tension 14.5 N/mm 2 Temperature resistance 0.7 kcal/mh°C, – 60°C to + 120°C Dimensional stability/Martens + 40°C Linear expansion coefficient + 40 x10–6 1°C Tempering up to + 120°C/1h Shelf life at least 2 years Total weight 500 g Technical data Application overview