TDS-WS-801-EN_1420 (Highly Swellable Joint Waterstop)

قناة عامة / جداول المواصفات

1. VELOSIT ® WS 801 Applica'onfield VELOSIT WS 801
عبارة عن حاجز مائي قابل للتضخم بالماء يستخدم في العزل المائي للبناء على المفاصل. التطبيق النموذجي على الحقول إلى جانب الآخرين هو كما يلي:
• العزل المائي للبناء
على الوصلات بين صب الخرسانة المختلفة
• العزل المائي لمفاصل قطع المنشار
• تسرب المياه من اختراق الأنابيب • العزل المائي لمفصل بلاطة الجدار
• سدادة مائية قابلة للانتفاخ لمعالجة بناء؟
على المفاصل بين صب الخرسانة. يتضخم فيلوسيت
دبليو اس 801 حتى مع مياه الصرف الصحي التي تحتوي على أحمال ملح مرتفعة.
دبليو اس 801 عبارة عن حاجز مائي ينتفخ تحت ملامسة الماء. يتم تطبيقه على الخرسانة السابقة التي تصب في مركز البناء أو وصلة التمدد.
يتم تثبيت يتم تثبيت فيلوسيت على الخرسانة.
• قدرة انتفاخ بنسبة 1000٪ ، قابلة للعكس تمامًا لعدد غير محدود من الدورات
• ثبات الأبعاد ، عدم الانجراف كما هو الحال مع محطات المياه البنتونيت. • التورم المتخلف ، يبدأ زيادة الحجم لعدة ساعات بعد ملامسة الماء
• ضغط التورم أكبر من 5 بار (73 رطل / بوصة مربعة) ، مقاومة قصوى لضغط الهيدروستات • يقاوم 50 م (160 Q.) ضغط الماء acc. إلى EN 12390-8 Applica'on 1.) يعد إعداد الركيزة على VELOSIT WS 801 مناسبًا للوصلات المقواة في الأجسام الخرسانية. قم بإزالة المواد المنفصلة ومواد تكسير الروابط من الخرسانة الأولى (على سبيل المثال ، Founda؟ on and slab). يجب أن يكون السطح مفتوحًا مساميًا وتحمل الحمولة. الحد الأدنى من متطلبات القوة هو 15 ميجا باسكال 1420
يتم تثبيت فيلوسيت مفصل شديد الانتفاخ مجالات تطبيق توقف المياه يتم تثبيت فيلوسيت عبارة عن حاجز مائي قابل للانتفاخ بالماء مصنوع من مزيج من اللدائن الحرارية الخاصة وعوامل الانتفاخ المركبة لإنتاج حاجز مائي قابل للانتفاخ من الانتفاخ الفريد القدرة. تم تصميم VELOSIT WS 801 لتقليل الجيب على الجانبين. يستخدم VELOSIT WS 801 لإغلاق فواصل البناء. تشمل مجالات التطبيق النموذجية ما يلي:
• العزل المائي لفواصل البناء بين مصبات الخرسانة • العزل المائي لفواصل قطع المنشار • تسرب المياه من اختراق الأنابيب • العزل المائي لمفاصل ألواح الجدران خصائص VELOSIT WS 801 تتضخم حواجز المياه البلاستيكية الحرارية تدريجياً عند ملامستها للماء. يتم لصق VELOSIT WS 801 بمادة لاصقة أو يتم تثبيته على الخرسانة المتصلدة الموجودة قبل صب الخرسانة الطازجة. يعرض VELOSIT WS 801 العديد من الخصائص الفريدة بما في ذلك: • الملف الشخصي المصمم لزيادة القفل بالخرسانة الطازجة. وضع مركزيًا على شكل "V" بالإضافة إلى الحواف الدائرية لتقليل مخاطر التعرّض للجيوب
• + 1000٪ قدرة انتفاخ في مياه الشرب ؛ قابل للعكس تمامًا لعدد غير محدود من الدورات • + 750٪ قدرة انتفاخ في مياه البحر • مستقر الأبعاد ؛ لا يغسل مثل مواضع المياه البنتونيت. تبدأ زيادة الحجم بعد عدة ساعات من ملامسة الماء ، لتصل إلى الانتفاخ الكامل في 8 أيام • ضغط الانتفاخ> 5 بار (73 رطل / بوصة مربعة) ، مقاومة شديدة ضد الضغط الهيدروستاتيكي • مقاومة 50 بارًا أو 50 مترًا من رأس الماء (160 قدمًا) عند الاختبار على EN 12390-8 VELOSIT® WS 801 High Swellablity Thermoplastic Waterstop

2. VELOSIT ® WS 801 (2175 رطل / بوصة مربعة). قم بإصلاح عيوب السطح الكبيرة باستخدام VELOSIT RM 202. 2.) المعالجة نظرًا لضغط الانتفاخ الهائل ، يجب تثبيت VELOSIT WS 801 على الأقل. 50 مم (2 بوصة) من كل حافة. لا تستخدم VELOSIT WS 801 على الجدران الخرسانية التي يقل طولها عن 120 مم. التثبيت بالمسامير: يمكن تثبيت VELOSIT WS 801 في أول ثانية من الخرسانة. قم برمي المسامير كل 15 سم (6 بوصة) بمسدس مسمار (على سبيل المثال Hil؟ DX 76) من خلال VELOSIT WS 801 في الخرسانة. قم بقص التداخلات أو المعابر أو نهايات حاجز الماء بزاوية 45 درجة واتصل بدون فجوة. المناطق المجوفة التي يزيد طولها عن 4 مم قد تقلل من كثافة الماء بشكل كبير. لا يمكن معالجة أنابيب Plas ؟c إلا باستخدام VELOSIT WS 801 حتى DN 50 (2 بوصة) بالماء البارد وما يصل إلى DN 25 (1 بوصة) لأكثر من 30 درجة مئوية (86 درجة فهرنهايت) درجة حرارة الماء. نظرًا لارتفاع ضغط الانتفاخ ، فقد تنهار أنابيب البلازما تحت الحمل. يتم نفاذ الأقطار الأكبر فقط باستخدام الأنابيب المعدنية. 3.) علاج VELOSIT WS 801 لا يتطلب معالجة. تجنب الماء الراكد على حاجز الماء لأن هذا قد يؤدي إلى انتفاخ مبكر في المادة. بسبب التورم المتأخر ، لا يمثل التلامس مع مياه الأمطار على المدى القصير مشكلة. Es'ma'ng يتم احتساب المبلغ المطلوب مع الطول المخطط لعزل المياه المشترك. تنظيف VELOSIT WS 801 لا يسبب أي اتساخ. يمكن تنظيف المواد المتسخة بقطعة قماش مبللة. لا تقم بتركيب مادة منتفخة بالفعل. انتظر حتى تجف المادة تمامًا وحققت أبعادها الأصلية. ميزات الجودة اللون: أزرق الأبعاد: 5 × 20 مم الوزن: 0.12 كجم / م (0.24 رطل / ياردة) درجة حرارة الركيزة: 5 - 35 درجة مئوية (40-95 درجة فهرنهايت) عدم نفاذية الماء. EN 12390-8: - Posi؟ ve side: 5 بار (73 رطلًا لكل بوصة مربعة) امتصاص الماء: 1.2 كجم / م (2.4 رطل / ياردة) أقصى انتفاخ - مياه الشرب: 1060٪ - مياه البحر: 750٪ - مالح الماء: 580٪ التعبئة والتغليف يتم توريد VELOSIT WS 801 على شكل لفات á 50 م (163 قدم). 5 لفات معبأة في صندوق (حوالي 27 كجم / 59 رطلاً). التخزين يمكن تخزين VELOSIT WS 801 في عبوات أصلية غير مفتوحة لمدة 5 سنوات عند 5-35 درجة مئوية (40-95 درجة فهرنهايت) في مكان تخزين جاف محمي من أشعة الشمس.

3. سلامة VELOSIT ® WS 801 برجاء مراعاة ورقة بيانات سلامة المواد الصالحة الفعلية واتباع إجراءات السلامة الموضحة للتعامل مع المنتج. إن التوصيات VELOSIT WS 801 متاحة فقط للمتقدمين المحترفين. يتم تحديد جميع ميزات المنتج الموصوفة بموجب شروط المختبر الخاضعة للرقابة وفقًا للمعايير الدولية ذات الصلة. قد تختلف القيم المحددة ضمن شروط موقع العمل عن القيم المذكورة. يرجى دائمًا استخدام أحدث نسخة من ورقة البيانات هذه والمتوفرة على موقعنا على الإنترنت www.velosit.de. الشركة المصنعة VELOSIT GmbH & Co. KG Industriepark 7 32805 Horn-Bad Meinberg ألمانيا www.velosit.de

+971600541110
+971 2566 2610
https://wa.me/97172281030

المشاركة على مواقع التواصل الاجتماعي

مشاركة الرابط

استخدام رابط دائم للمشاركة في وسائل الاعلام الاجتماعية

المشاركة مع صديق

برجاء تسجيل الدخول لإرسال هذا document بالبريد الالكتروني!

تضمين في موقعك

Select Link to start with 

1. VELOSIT ® WS 801 Applica'on fields VELOSIT WS 801 is a water swellable waterstop used for waterproofing of construc?on joints. Typical applica?on fields besides others are as follows: • Waterproofing of construc?on joints between different concrete pours • Waterproofing of saw cut joints • Waterproofing of pipe penetra?ons • Waterproofing of the wall-slab joint • Swellable waterstop for the treatment of construc?on joints between concrete pours. VELOSIT WS 801 swells even with sewage water containing elevated salt loads. Proper'es VELOSIT WS 801 is a waterstop that swells under contact with water. It is applied on the previous concrete pour into the center of the construc?on or expansion joint. VELOSIT WS 801 is nailed to the concrete. • 1000% swelling capacity, fully reversible for an unlimited number of cycles • Dimensional stable, no wash-out like with Bentonite waterstops • Retarded swelling, volume increase starts several hours aQer water contact • Swelling pressure of > 5 bar (73 psi), extreme resitance against hydrosta?c pressure • Resists 50 m (160 Q.) water pressure acc. to EN 12390-8 Applica'on 1.) Substrate prepara'on VELOSIT WS 801 is suitable for reinforced joints in concrete bodies. Remove separa?ng and bondbreaking substances from first concrete sec?on (for example founda?on and slab). Surface should be open porous and load bearing. Minimal strength requirement is 15 MPa 1420 Page of 1 3 VELOSIT ® WS 801 Highly Swellable Joint Waterstop Application fields VELOSIT WS 801 is a water swellable waterstop manufactured from a blend of proprietary thermoplastics and swelling agents compounded to produce a re-swellable waterstop of unique swelling ability. VELOSIT WS 801 is engineered to reduce pocketing on the sides. VELOSIT WS 801 is used to seal construction joints. Typical application fields include : • Waterproofing of construction joints between concrete pours • Waterproofing of saw cut joints • Waterproofing of pipe penetrations • Waterproofing of the wall-slab joints Properties VELOSIT WS 801 thermoplastic waterstops gradually swell when in contact with water. VELOSIT WS 801 is either glued with an adhesive or nailed to the existing hardened concrete prior to pouring of fresh concrete. VELOSIT WS 801 exhibits many unique properties including: • Profile engineered to increase keying with fresh concrete; centrally placed “V” in addition to rounded edges for reduced risk of pocketing • + 1000% swelling capacity in potable water; fully reversible for an unlimited number of cycles • + 750% swelling capacity in sea water • Dimensionally stable; does not wash-out like Bentonite waterstops • Delayed swelling; volume increase starts several hours after water contact, reaching full swellability in 8 days • Swelling pressure of > 5 bar (73 psi), extreme resistance against hydrostatic pressure • Resists 50 Bars or 50 m water head (160 ft.) when tested to EN 12390-8 VELOSIT ® WS 801 High Swellablity Thermoplastic Waterstop

2. VELOSIT ® WS 801 (2175 psi). Patch larger surface defects with VELOSIT RM 202. 2.) Processing Due to its enormous swelling pressure VELOSIT WS 801 must be installed min. 50 mm (2”) from each edge. Do not use VELOSIT WS 801 on concrete walls of less than 120 mm cross-sec?on. Fixing with nails: VELOSIT WS 801 can be nailed to the first concrete sec?on. Shoot nails each 15 cm (6”) with a nail gun (for example Hil? DX 76) through VELOSIT WS 801 into the concrete. Cut overlaps, crossings or termina?ons of the waterstop in a 45° angle and connect without a gap. Hollow areas of more than 4 mm may reduce water?ghtness significantly. Plas?c pipes can only be treated with VELOSIT WS 801 up to DN 50 (2”) with cold water and up to DN 25 (1”) for more than 30°C (86°F) water temperature. Due to the high swelling pressure plas?c pipes may collapse under load. Larger diameters are only permifed with metal pipes. 3.) Curing VELOSIT WS 801 does not require curing. Avoid standing water on the waterstop as this may result in apremature swelling of the material. Because of the retarded swelling a short term contact with rain water is not a problem. Es'ma'ng The required amount is calculated with the planned length of the joint waterproofing. Cleaning VELOSIT WS 801 does not cause any dirt. Dirty material can be cleaned with a moist cloth. Do not install material that has already swollen. Wait un?l the material has completely dried and achieved its original dimensions. Quality features Color: blue Dimensions: 5 x 20 mm Weight: 0.12 kg/m (0.24 lb./yd.) Substrate temperature: 5 – 35°C (40 – 95°F) Water impermeability acc. EN 12390-8: - Posi?ve side: 5 bar (73 psi) Water absorp?on: 1.2 kg/m (2.4 lb./yd.) Maximum swelling - potable water: 1060 % - sea water: 750 % - saline water: 580 % Packaging VELOSIT WS 801 is supplied in rolls á 50 m (163’). 5 rolls are packaged in a box (approx. 27 kg/59lbs.). Storage VELOSIT WS 801 can be stored in unopened original packs for 5 years at 5 – 35°C (40 – 95 °F) in a dry storage place protected against sunlight.

3. VELOSIT ® WS 801 Safety Please observe the actual valid material safety data sheet and follow the described safety measures for handling of the product. Recommenda'ons VELOSIT WS 801 is only available for professional applicators. All described product features are determined under controlled laboratory condi?ons according to the relevant interna?onal standards. Values determined under job site condi?ons may deviate from the stated values. Please always use the latest version of this data sheet available from our website www.velosit.de . Manufacturer VELOSIT GmbH & Co. KG Industriepark 7 32805 Horn-Bad Meinberg Germany www.velosit.de

طرق العرض

  • 5037 عدد المشاهدات
  • 4000 موقع المشاهدات
  • 1037 المشاهدات المدمجة

الإجراءات

  • 0 مشاركات اجتماعية
  • 4
  • 0
  • 1تعليقات

عدد المشاركات

  • 0  فيسبوك
  • 0  توتير
  • 0  ينكدين

يتضمن 4

  • 3 www.sab-cs.com
  • 22 161.97.92.48
  • 1 sab-cs.com
  • 178 www.sab-us.com

زوار الموقع 370919