4. VELOSIT ® RM 211 relevant interna8onal standards. Values determined under job site condi8ons may deviate from the stated values. Please always use the latest version of this data sheet available from our website www.velosit.de . Manufacturer VELOSIT GmbH & Co. KG Industriepark 7 32805 Horn-Bad Meinberg Germany www.velosit.de 2419 page of 4 4

1. VELOSIT ® RM 211 Applica'on fields VELOSIT RM 211 is a crystalline cemen88ous repair mortar for concrete restora8on acc. to EN 1504-9. It creates a smooth surface for crystalline waterproof coa8ngs. Typical applica8on fields besides others are as follows: • Repair of surface defects on concrete • Overlays and repairs on concrete structures like dams, bridges, beams, balconies, facades • Applica8on on horizontal and ver8cal • Filling of blow holes, honeycombs and surface roughness • Applica8on thickness from feather-edge to 25 mm (1”) System components: Crystalline plug cement: VELOSIT PC 222 Structural repair mortar: VELOSIT RM 211 Waterproofing: VELOSIT CW 111 Proper'es VELOSIT RM 211 is a shrinkage compensated crystalline cemen88ous repair mortar with quick strength development. VELOSIT RM 211 binds the mixing water fast reducing or completely elimina8ng the need for water curing and protec8on. VELOSIT RM 211 creates an extremely well bonded, rigid abrasion resistant layer on the substrate. VELOSIT RM 211 surpasses the requirements of EN 1504-3 class R3 for concrete repair (CR) and can be used according to the principles 3, 4 and 7 acc. to EN 1504-9. VELOSIT RM 211 can be applied by trowel or suitable spray equipment. • Minimal shrinkage/expansion under dry resp. wet curing condi8ons minimizing the risk of micro-cracking • Excellent workability • Fiber reinforced • 45 min. working 8me and 12 MPa (1740 psi) compressive strength a\er 4 hours 2419 page of 1 4 VELOSIT ® RM 211 Crystalline Concrete Repair Mortar R3 EN1504-3

3. VELOSIT ® RM 211 product as described above into the feed hopper of the spray machine and spray con8nuously. If a smooth surface is required, follow with a trowel shortly a\er material is sprayed. Work in sec8ons. Long spray interrup8ons may result in clogging of the spray hose. The product may cure a lot faster if the hose is exposed to direct sunlight. Always empty and flush the machine a\er spraying or before long spray interrup8ons. VELOSIT RM 211 is a fast curing material and may be hard to remove if le\ in the machine. 3.) Curing VELOSIT RM 211 does not require long term curing as it reacts rela8vely fast with water. Only under hot weather or very dry condi8ons water curing for 3 – 4 hours is required. Es'ma'ng Repair of surface defects: 25 kg (55 lbs.) VELOSIT RM 211 result in approx. 15.2 liter (0.53 \ 3 ) cured mortar. Surface Coa8ng: 10 kg (22 lbs.) * VELOSIT RM 211 per m 2 (10.7 \ 2 ) for 6 mm (1/4”) dry mortar thickness on smooth substrates. Depending on surface roughness applica8on rates can be significantly higher. * 10 kg VELOSIT RM 211 powder + 1.8kg water, i.e. 11.8kg mixed material per 6 mm and m 2 Cleaning VELOSIT RM 211 can be removed in the fresh state with water. Once it has cured acidic cleaners like muria8c acid and mechanical cleaning are required. Quality features Color: gray Mixing ra8o by weight: 100 : 18 Mixing ra8o by volume: 100 : 28 Density: 1.6 kg/l Substrate temperature: 5 – 35 °C (40 – 95 °F) Ini8al set: 75 min. Final set. 120 min. Compressive / flexural strength: 4 hours: 12 / 3 MPa (1740/335 psi) 24 hours: 22 / 4 MPa (3190/580 psi) 7 days: 28 / 6 MPa (4060/870 psi) 28 days: 40 / 8 MPa (5800/1160 psi) Chloride ions: < 0.05 % Carbona8on resistance: passed Capillary water absorp8on: 0.1 kg/m 2 x h 0.5 Adhesive strength*: 2.0 MPa (290 psi) Restrained shrinkage*: 2.0 MPa (290 psi) Fire ra8ng EN13501-1: Class A1 *acc. EN 1542. Adhesion depends very much on proper surface prepara8on! Packaging VELOSIT RM 211 is available in 25 kg (55 lb.) water8ght plas8c bags. Storage VELOSIT RM 211 can be stored in unopened original packs for 12 months at 5 – 35 °C (40 – 95 °F) in a dry storage place protected against sunlight. Safety Please observe the actual valid material safety data sheet and follow the described safety measures for handling of the product. Recommenda'ons VELOSIT RM 211 is only available for professional applicators. Never add water to VELOSIT RM 211 when it has started to set. S8ffened material must be disposed. All described product features are determined under controlled laboratory condi8ons according to the 2419 page of 3 4

2. VELOSIT ® RM 211 • Final strength of more than 40 MPa (5800 psi) a\er 28 days • Open to foot traffic a\er 3 – 4 hours • Excellent adhesion to properly prepared concrete • Water curing only under hot and dry condi8ons required for max. 4 hours • Good resistance against CO 2 and Chloride penetra8on due to a very 8ght pore structure • Good resistance against aggressive media with a pH range of 3-12 and against so\ water with low ion content • Good weathering resistance • Good sulfate resistance • Light gray color close to concrete color Applica'on 1.) Substrate prepara'on VELOSIT RM 211 is designed for concrete substrates. Steel may be coated with a VELOSIT CP 201 bonding bridge. a.) Steel must be prepared to a purity of SA 2.5 acc. SIS 05 5900. Apply a corrosion protec8on coat on rebar with VELOSIT CP 201. Other steel areas can be primed with VELOSIT PR 303 with a full broadcast. Steel may expand and contract differently under temperature changes than a cemen88ous mortar. Thus steel applica8on is only recommended if steel is embedded in larger concrete bodies or the temperature is not subject to major changes. b.) Concrete substrates must be prepared with sand blas8ng, shot blas8ng or ideally high pressure water blas8ng (> 100 bar/ 1450 psi) to remove all bond breaking substances. Remove all carbonated concrete. Test with Phenolphthalein or other suitable indicator un8l concrete with sufficient alkalinity for rebar protec8on is reached. If rebar is exposed remove concrete at least 6 mm (1/4”) behind rebar to fully embed the steel into VELOSIT RM 211. Substrate must be rough, open porous and load bearing. The minimum requirement for adhesive strength is 1.5 MPa (218 psi) and for the compressive strength 25 MPa (3625 psi). Lower strength values can be accepted if lower adhesive strength is acceptable. Ac8ve water leaks must be treated and fully stopped with VELOSIT PC 221. Leaking cracks need to be sealed with a PU injec8on material. Before the applica8on of VELOSIT RM 211, dampen the substrate with clean water to a saturated surface dry (SSD) condi8on. 2.) Processing Mixing: Mix VELOSIT RM 211 with 17 – 20 % potable water, i.e. 4.3 – 5.0 l (1.1 – 1.3 gal.) water per 25 kg (55 lb.) bag. Fill 17 % mixing water (4.3 l per bag) into a suitable bucket and mix the powder with a slow speed drill (300 – 600 rpm) into the water un8l a lump-free mix is achieved. Add up to 3 % water under s8rring to adjust desired consistency is. Clean mixing paddle immediately a\er mixing. The product is workable for 45 min. at 23 °C. a.) Trowel applica8on: Apply a slurry coat of VELOSIT RM 211 by scrubbing material with a wet sponge into the concrete surface. Trowel VELOSIT RM 211 fresh in fresh into the slurry coat. The product can be applied up to 25 mm (1”) on ver8cal areas. Make sure to work in sec8ons that can be finished within 30 min. Rebars and other penetra8ons must be fully embedded into the mortar. b.) Spray applica8on: Use suitable spray machines such as: - PFT GmbH: PFT G4 - HighTech GmbH: HighComb Big - Wagner GmbH: PC 25 - Putzmeister GmbH: SP12 or MP 25 - Inotec GmbH: INOMAT-M8 In mixing pumps feed the powder into the product hopper and adjust the water to the desired consistency. With mortar pumps add the mixed 2419 page of 2 4