4 mm thick, APP modified bituminous membrane, reinforced with non woven polyester mat
Description
High Performance polymer (APP) modified bituminous membrane, reinforced with
180 g/m2 non-woven polyester mat. The polyester combines high tensile strength and
elongation. The specially used polymer modifier has a great resistance to Ultra-Violet
radiation.
Features
• High flexibility at low temperature and stability at high temperatures
• Durable and easy to apply
• Remarkable resistance to aggressive attack of salts and chemicals
• High tensile strength and elongation
• Excellent tear and puncture resistance
Function
Used as single layer as tanking in basements or for waterproofing of roofs. A single
layer followed by a layer of mineral surfaced DS can be used for exposed roofs.
Instructions for Application
The membrane can be installed fully bonded or loose-laid by torch welding.
The substrate should be cleaned and primed with AWAZEL PRIMER D 41 and
allowed to dry. Torching should be done by skilled workers and should be controlled
so that only the PE film is melted and the asphalt coating is softened sufficient to
bond the membrane. All lap joints should be smoothed and sealed using a heated
round-nosed trowel. The heat of the gas flame should be applied to the trowel. In
loose-laid applications, only the lap joints, areas around penetrations (pipes etc.),
upstands and a 30 cm wide strip around the perimeter of the work should be fully bonded.
Upstands and flashings should be installed using 1 M wide pieces cut from the length of
the roll. (The overlap joints should be 5 to 10 cm at the sides and 15 cm at the end)
Coverage
1.12 m per layer for flat surfaces
Health & Safety
All safety measures should be taken during application. Fire extinguishers should be
available on the site. Workers should wear on personnel protective tools such as gloves
and goggles during application.
Packing
It is produced in rolls of 1 x 10 meters. The rolls are palletized and shrink-wrapped.
Surfacing
Standard surfacing is fusible P.E. Film on both sides. Different combination of to surfacing
are available upon request such as sand, coloured minerals, etc…
Storage & Material Handling
The rolls should always be stored vertically in a shaded area. Normally the pallets should
not be stacked one over the other. However, if a wooden board is used in between, two
pallets may be stacked one over the other.
Description
High Performance polymer (APP) modified bituminous membrane, reinforced with
180 g/m2 non-woven polyester mat. The polyester combines high tensile strength and
elongation. The specially used polymer modifier has a great resistance to Ultra-Violet
radiation.
Features
• High flexibility at low temperature and stability at high temperatures
• Durable and easy to apply
• Remarkable resistance to aggressive attack of salts and chemicals
• High tensile strength and elongation
• Excellent tear and puncture resistance
Function
Used as single layer as tanking in basements or for waterproofing of roofs. A single
layer followed by a layer of mineral surfaced DS can be used for exposed roofs.
Instructions for Application
The membrane can be installed fully bonded or loose-laid by torch welding.
The substrate should be cleaned and primed with AWAZEL PRIMER D 41 and
allowed to dry. Torching should be done by skilled workers and should be controlled
so that only the PE film is melted and the asphalt coating is softened sufficient to
bond the membrane. All lap joints should be smoothed and sealed using a heated
round-nosed trowel. The heat of the gas flame should be applied to the trowel. In
loose-laid applications, only the lap joints, areas around penetrations (pipes etc.),
upstands and a 30 cm wide strip around the perimeter of the work should be fully bonded.
Upstands and flashings should be installed using 1 M wide pieces cut from the length of
the roll. (The overlap joints should be 5 to 10 cm at the sides and 15 cm at the end)
Coverage
1.12 m per layer for flat surfaces
Health & Safety
All safety measures should be taken during application. Fire extinguishers should be
available on the site. Workers should wear on personnel protective tools such as gloves
and goggles during application.
Packing
It is produced in rolls of 1 x 10 meters. The rolls are palletized and shrink-wrapped.
Surfacing
Standard surfacing is fusible P.E. Film on both sides. Different combination of to surfacing
are available upon request such as sand, coloured minerals, etc…
Storage & Material Handling
The rolls should always be stored vertically in a shaded area. Normally the pallets should
not be stacked one over the other. However, if a wooden board is used in between, two
pallets may be stacked one over the other.
طرق العرض
- 2929 عدد المشاهدات
- 2252 موقع المشاهدات
- 677 المشاهدات المدمجة
الإجراءات
- مشاركات اجتماعية
- 0
- 0
- 0تعليقات
عدد المشاركات
- 0 فيسبوك
- 0 توتير
- 0 ينكدين
يتضمن 5
- 40 www.sab-us.com
- 10 161.97.92.48
- 4 161.97.92.48:8011
- 154 www.google.com
- 8
-
LAVATEX 2000
13259 الآراء١٧ تشرين الثاني نوفمبر ٢٠٢٠ -
الوقاية من الحرارة والرطوبة العزل المائي
8111 الآراء٦ أيار مايو ٢٠٢١ -
DCL مطابقة منتج مختبرات بلدية دبي
7856 الآراء٢١ آب أغسطس ٢٠٢٠ -
Dr. Fixit UniProof 4000 Waterproof Roof & Protective Coating
7524 الآراء٢ آب أغسطس ٢٠٢١ -
Weber Product List
7505 الآراء٢٢ تشرين الثاني نوفمبر ٢٠٢١ -
Wurth sealants & Adhesives
7273 الآراء٢٣ كانون الثاني يناير ٢٠٢١ -
TDS-WS-801-EN_1420 (Highly Swellable Joint Waterstop)
7156 الآراء٥ كانون الثاني يناير ٢٠٢١ -
Optimization Methodology To Implement Thermal
7109 الآراء٢١ آب أغسطس ٢٠٢٠ -
VELOSIT® TDS-RM-211-EN_2419 ( R3 مونة بلورية لإصلاح الخرسانة)
6805 الآراء٥ كانون الثاني يناير ٢٠٢١ -
AWAZEL PU 250 White
6675 الآراء٤ آب أغسطس ٢٠٢١ -
TDS-PC-221-EN_2319 (Plug Cement)
6554 الآراء٥ كانون الثاني يناير ٢٠٢١ -
طبقات نظام العزل كومبو رووف
6298 الآراء٢١ آب أغسطس ٢٠٢٠ -
VELOSIT® TDS-CW-111-EN_2319 (High Strenght Crystalline Waterproofing Slurry)
6259 الآراء٥ كانون الثاني يناير ٢٠٢١ -
شرح الطريقة المثلى لتنفيذ أعمال العزل بنظام الكريستال للمنشآت حسب المواصفات القياسية ل ساب
6161 الآراء١٣ أيار مايو ٢٠٢١ -
ساعة مع شمس البوادي- الخرسانة مسبقة الصنع - البريكاست - 21
6064 الآراء٢٦ آب أغسطس ٢٠٢٠ -
VELOSIT® CA 113 Crystalline Hydrophobic Waterproofing Admixture
5999 الآراء١٢ كانون الثاني يناير ٢٠٢١ -
Approved Materials (TDS) for Sabtron Combo System
5900 الآراء١٧ تشرين الثاني نوفمبر ٢٠٢٠ -
Fosroc Conbextra EPGP
5791 الآراء١٧ تشرين الثاني نوفمبر ٢٠٢٠ -
Dr. Fixit PVA BOND.
5690 الآراء٢٨ تموز يوليو ٢٠٢١ -
VELOSIT® TDS-PC-222-EN_2319-1 (Plug Cement and Starter)
5498 الآراء٥ كانون الثاني يناير ٢٠٢١