1. RAK PROOF is a specially formulated single pack, high quality, elastomeric waterproof coating. It has outstanding durability, resistance to weathering and a very high degree of flexibility. • One component;ready to apply direct from the can. • Liquid application means details are simplified and there are no joints in the membrane • Highly elastic, cures to give a permanently flexible resilient barrier over a wide range of tempretures. • Rapid installation;significantly reduces time spent on preparatory works and detailing. • Excellent adhesion can be applied to a wide range of substrates. Contineous adhesion prevents lateral migration of water • Impervious-outstanding barrier properties ensure protection against corrosive soil conditions. • Excellent resistance to oxidation and embrittlement • Mechanical damage to the membrane can be easily repaired by spot application. (Acrylic Waterproof) 201 - RAK PROOF ADVANTAGES As with all chemical products, caution should always be exercised. Protective clothing, such as gloves and goggles, should be worn (see packaging for specific instructions). Treat any splashes to the skin or eyes with fresh water immediately. Should any of the product be accidentally swallowed, do not induce vomiting but call for medical assistance immediately. Ensure the container is available for the medical attendant to examine any relevant instructions and contents details. Reseal all containers after use and ensure product is stored as instructed on the safety section of the labeling. HEALTH AND SAFETY The support must be clean, free of dust, dirt, oil, grease and loose particles. When applying on metal surfaces, remove rust and contamination for best results. Apply with brush, roller or an appropriate spray. Apply a primer the coat of RAK Proof (80% RAK Proof + 20% water) with brush, roller or spray. Once the primer coat has completely dried, apply a minimum two coats of undiluted RAK Proof. It is important to ensure that coat has totally cured (i.e. minimum 8 hours at 30°C) before applying the next coat. For better results, a glass fibre mat is reinforced into the first coat while it is wet, at expansion areas and joints with parapets. APPLICATION Must be protected between 5°C and 30°C. 12 months in unopened airtight containers. SHELF LIFE Clean all tools with water after use CLEANING • To be used in most types of roofs, such as concrete, metal, asbestos, etc. • Ideal for waterproofing of car park decks and exposed surfaces in water prone systems such as foundations, basements, tunnels, ground floors, suspended floors, car decks, roof terraces, balconies, patios, bridges, inspection pits, sewage works, inverted roofs, bathrooms, kitchen, toilets etc. • Recommended as a protective membrane for P.U. installation. USES 1 kg/m2 per coat, approximately (depending on the support and the means of application) COVERAGE Wt : 5Kg Wt : 20Kg CHARACTERISTICS Density pH Solid content Elongation at break Color Toxicity Tack free time @30°C Time to full cure @30°C Typical cured membrane properties (at 28 days) Elongation Tensile Strength (ASTM D4541) Recovery from 200% elongation (ASTM D412) Tear resistance (ASTM D624) Permeability @ 5 bar pressure 7th Day Artificial weathering Service tempreture (contineous ambient) 1.25 g/cc 885 60 + 2% by weight 400% White Non Toxic 8 hours 48 hours @ 1.3mm thickness 400 1.5 N/mm2 95% 14N NIL No loss of flexibility after 4000 hours exposure -40°C to 70°C ORDERING GUIDE 201 ASTM D 412, D 4541 MSEN 12390 PT 8:2000 5 kg /20 kg Packs White / Grey PRODUCT NO. STANDARDS PACKAGING COLOR F L O O RIN G & TI L IN G W A T E R P R O O FIN G B ON D IN G A G E N T S S E ALA N T S & MO R T A R S S P E CIA L I T Y P R O DU C T S 11 TECHNICAL DATA SHEET