Public Channel / Data Sheets

Crystalline Capillary Waterproofing Coating for Concrete

Description
SAB®Crystal Coat CP 212
is a one component, capillary crystalline, waterproof coating, which waterproofs concrete structures by forming insoluble
crystals in concrete capillaries. SAB®Crystal Coat CP 212 waterproofs both from negative and positive direction and is
ideally suited for basement water proofing. SAB®Crystal Coat CP 212 cures to a hard-robust abrasion resistant coating.

Usage:
Water Retaining Structures such as water tanks and swimming pools, reservoirs, dams, canals, sewerage & water treatment
works and concrete pipes. Water Excluding Structures such as foundations and shallow basements, tunnels and subways,
underground cap parks, Inspection pits and lift shafts, Sea defense walls, Bridge decks, Jetties Retaining walls & Civil substructures.

ADVANTAGES
• Negative and Positive waterproofing
• Replaces ineffective sheet membranes.
Seals shrinkage cracks up to 1/64” (0.4 mm) width. Reduced chloride permeability.
• Protect concrete and reinforcement from corrosion due to water born substances like chlorides and sulphates.
• Easy to apply product and Excellent adhesion
• Non-toxic and suitable in potable water containment.
• Not a vapor barrier - allows concrete to breathe. • Negligible interference with water reducers & plasticizers.
• Negligible effect/influence on slump and air entrainment.
• Impervious to physical damage and deterioration
• Non-toxic, inorganic, zero VOC (0%)
• Less costly than traditional methods of waterproofing.
• Economic efficiency
• Improves resistance of concrete structures against weathering and chemical attack.

PACKAGING
20kg Bag
25kg Plastic Pail
COVERAGE
Apply in 2 to 3 coats to achieve an overall thickness of 1.5-2.0mm with an overall material consumption of 2.0-3.0kg/m2.
6m to 10m total coverage.

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 

2. Application Temperature 5 ° C to 45 ° C Mixing Ratio 20 Kg: 6 Litres of water Pot life 2 to 3 hours Setting time 3 hours approx. (Typical Properties tested at 25 ° C under laboratory conditions) (The properties shown above were obtained under laboratory conditions). All values given are subject to 10% tolerance PREPARATION OF SURFACE Ensure that all dust, dirt and foreign matter are scraped and brushed away. Also ensure the surfaces are free from salts, oil, grease and ridges, and protect all adjacent surfaces not to be covered. If repair area is dry at the time of repair, moisten substrate before application of SAB ® Crystal Coat CP 212 . APPLICATION AND CLEANING OF TOOLS *Add the powder to water and use a power agitator until the mix is homogenous. Mix the powder with water in the ratios as shown in the Technical Data and apply in 2 to 3 coats to achieve an overall thickness of 1.5 - 2.0mm with an overall material consumption of 2.0 - 3.0kg/m2. *Apply using brush or spray, leaving 3 hours between coats. SAB ® Crystal Coat CP 212 should be used within 1 hour. *Cured CRYSTACEM - CP should be kept moist for 5 to 7 days to promote crystal formation EQUIPMENT CLEANING Clean all equipment and tools with water immediately after use. HEALTH AND SAFETY PPE’s Gloves, goggles & suitable mask must be worn. Precautions: Contact with skin, eyes, etc. must be avoided. Hazard: Regarded as non - hazardous for transportation. Disposal: Do not reuse bags or containers. To be disposed off as per local rules & regulations. PACKING AND STORAGE PACKAGING 20kg Bag 25kg Plastic Pail COVERAGE A pply in 2 to 3 coats to achieve an overall thickness of 1.5 - 2.0mm with an overall material consumption of 2.0 - 3.0kg/m2. 6m to 10m total coverage.

1. 212 CP l Coat Crysta ® SAB Crystalline Capillary Waterproofing Coating for Concrete Description SAB ® Crystal Coat CP 212 is a one component, capillary crystalline, waterproof coating, which waterproofs concrete structures by forming insoluble crystals in concrete capillaries. SAB ® Crystal Coat CP 212 waterproofs both from negative and positive direction and is ideally suited for basement water proofing. SAB ® Crystal Coat CP 212 cures to a hard - robust abrasion resistant coating. Usage : Water Retaining Structures such as water tanks and swimming pools, reservoirs, dams, canals, sewerage & water treatment works and concrete pipes. Water Excluding Structures such as foundations and shallow basements, tunnels and subways, underground cap parks, Inspection pits and li ft shafts, Sea defense walls, Bridge decks, Jetties Retaining walls & Civil substructures. ADVANTAGES • Negative and Positive waterproofing • Replaces ineffective sheet membranes. Seals shrinkage cracks up to 1/64” (0.4 mm) width. Reduced chloride permeability. • Protect concrete and reinforcement from corrosion due to water born substances like chlorides and sulphates. • Easy to apply product and Excellent adhesion • Non - toxic and suitable in potable water containment. • Not a v apor barrier - allows concrete to breathe. • Negligible interference with water reducers & plasticizers. • Negligible effect/influence on slump and air entrainment. • Impervious to physical damage and deterioration • Non - toxic, inorganic, zero VOC (0%) • Less costly than traditional methods of waterproofing. • Economic efficiency • Improves resistance of concrete structures against weathering and chemical attack. Technical data SAB ® Crystal Coat CP 212 Component Single Color / Form Grey Powder Bulk Density Approx. 1.5 kg/m3

Views

  • 2448 Total Views
  • 1859 Website Views
  • 589 Embeded Views

Actions

  • 0 Social Shares
  • 6
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 3

  • 10 www.sab-us.com
  • 11 161.97.92.48
  • 2 161.97.92.48:8011

Website Visitors - 489093