Kanz CRESPLUG HB - TDS

Public Channel / Data Sheets

CRESPLUG HB
Quick Setting Cemenetitious Plugging Compound

Description
CRESPLUG HB is a quick setting hydraulic cement compound used to instantly stop running water or
seepage in masonry or concrete. It is ready to use and requires only the addition of water before
plugging and sealing active leaks.

Uses
 Concrete and Masonry walls and floors.
 Stops active water or seepage under pressure through joints, cracks and holes in concrete or masonry.
 Interior and exterior areas for vertical and horizontal applications.
 For sealing cracks and construction joints in reservoirs and other water-retaining structures.
 Repairing honeycombs, cracks and joints.
 It is effective in sealing water leaks through concrete, concrete block walls, brickwork, earthenware
and almost all types of stones and masonry.

Advantages
 Chloride free, will not promote corrosion of reinforcement.
 Single component, only mixed with water.
 Stops active water leakages by setting instantly.
 Easy to use, no special equipment required.
 Very fast setting with rapid strength development.
 No cracking & No shrinkage.

Technical Properties
Color Grey
Pot life @ 25 °C 20 to 40 seconds
Initial setting time @ 25 °C 40 to 60 seconds ASTM C266
Final setting time @ 25 °C 2 to 4 minutes ASTM C266
Application Temperature 5 °C to 35 °C
Mixing Ratio 3.2 Parts Powder, 1 Part Water
All values given are subject to 5-10% tolerance.


Surface Preparation
Application surfaces must be structurally sound, free of loose or deteriorated concrete, free of dust, dirt, paint and other contaminants. Cracks or cavities to be sealed may need to be enlarged to increase the bonding area. Where surface contamination exists, concrete surfaces should be prepared by water blasting, girt blasting or wire brushing in the area of the leak in order to remove the laitance in preparation to receive the CRESPLUG HB.

Mixing
Mix 3.2 parts of CRESPLUG HB with 1 parts of clean water (3.2 kg of CRESPLUG HB with 1 kg of water). Mix to a stiff paste in a suitable mixing vessel, using a trowel or gloved hand. Do not mix it for more than 20 seconds. Due to the rapid set characteristics of the product, only prepare a quantity of mortar which can be placed within the prescribed set time. Mix the product with clean water to form a stiff paste and fill the void by pressing the paste into the damaged area for a minimum of 25 seconds for the pressurized water area & for the non pressurized water area apply the stiff paste in cracks and small holes & remove the hand which sets instantly. Once set remove excess material by cutting surface with a trowel or by scraper.
CRESPLUG HB
Quick Setting Cemenetitious Plugging Compound

All the tools and equipments must be cleaned by water after the application. After CRESPLUG is hardened, it can only be removed from the surface mechanically.
Coverage Coverage varies depends upon the water leaks.
Packing 5 kg, 10 kg and 15 kg Pail.
Storage Material must be stored in a covered area, away from direct sunlight and protected from extreme temperature. Must be protected from moisture and frost conditions.

Shelf life
Shelf life is 12 months in sealed original containers under recommended storage conditions. Once opened the material should be used as soon as possible.
Health & Safety
CRESPLUG HB is based on cement and thus can be irritating to the skin and eyes. Gloves and eye protection should be worn. As with all chemical products, care should be taken to avoid contact with skin, eyes, mouth and foodstuffs. Treat splashes to eyes and skin immediately, by thoroughly washing with clean water. If ingested seek medical attention.

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 
There are no comments for now.

Leave a comment

You must be logged in to post a comment.


2. CRESPLUG HB Quick Setting Cemenetitious Plugging Compound Page 2 of 2 Rev. 0 , June’19 Cleaning All the tools and equipments must be cleaned by water after the application. After CRESPLUG is hardened, it can only be removed from the surface mechanically . Coverage Coverage varies depends upon the water leaks . Packing 5 kg, 10 kg and 15 kg Pail . Storage Material must be stored in a covered area, away from direct sunlight and protected from extreme temperature. Must be protected from moisture and frost conditions . Shelf life Shelf life is 12 months in sealed original containers under recommended storage conditions. Once opened the material should be used as soon as possible . Health & Safety CRESPLUG HB is based on cement and thus can be irritating to the skin and eyes. Gloves and eye protection should be worn. As with all chemical products, care should be taken to avoid contact with skin, eyes, mouth and foodstuffs. Treat splashes to eyes and skin immediately, by thoroughly washing with clean water. If ingested seek medical attention . Disclaimer Kanz chemical Ind. LLC products are guaranteed against defective materials and are sold subject to standard terms and condition of sale, copies of which are available on request which are reasonable, care is taken compiling this technical data sheet, all recommendations regarding the use of product are made without guarantee since the conditions of use are beyond the company’s direct contro l. It is the customer’s responsibility to satisfy them that each product is fit for the purpose for which they intend to use it. Furthermore the specifications and description herein cannot be used to void a contract. *Refer material safety data sheet (MSDS) for further information.

1. CRESPLUG HB Quick Setting Cemenetitious Plugging Compound Page 1 of 2 Description CRESPLUG HB is a quick setting hydraulic cement compound used to instantly stop running water or seepage in masonry or concrete. It is ready to use and requires only the addition of water before plugging and sealing active leaks . Uses  Concrete and Masonry walls and floors .  Stops active water or seepage under pressure through joints, cracks and holes in concrete or masonry .  Interior and exterior areas for vertical and horizontal applications .  For sealing cracks and construction joints in reservoirs and other water - retaining structures.  Repairing honeycombs, cracks and joints.  It is effective in sealing water leaks through concrete, concrete block walls, brickwork, earth enware and almost all types of stones and masonry . Advantages  Chloride free, will not promote corrosion of reinforcement.  Single component, only mixed with water.  Stops active water leakages by setting instantly.  Easy to use, no special equipment required.  Very fast setting with rapid strength development.  No cracking & No shrinkage . Technical Properties Description Value Standard Color Grey - Pot life @ 25 ° C 20 to 4 0 seconds - Initial setting time @ 25 ° C 4 0 to 6 0 seconds ASTM C266 Final setting time @ 25 ° C 2 to 4 minutes ASTM C266 Application Temperature 5 °C to 3 5 °C - Mixing Ratio 3.2 Parts Powder, 1 Part Water - All values given are subject to 5 - 10% tolerance . Surface Preparation Application surfaces must be structurally sound, free of loose or deteriorated concrete, free of dust, dirt, paint and other contaminants. Cracks or cavities to be sealed may need to be enlarged to increase the bonding area . Where surface contamination exists, concrete surfaces should be prepared by water blasting, girt blasting or wire brushing in the area of the leak in order to remove the laitance in preparation to receive the CRESPLUG HB . Mixing Mix 3.2 parts of CRESPLUG HB with 1 parts of clean water (3.2 kg of CRESPLUG HB with 1 kg of water). Mix to a stiff paste in a suitable mixing vessel, using a trowel or gloved han d. Do not mix it for more than 2 0 seconds . Due to the rapid set characteristics of the product, only prepare a quantity of mortar which can be placed within the prescribe d set time. Mix the product with clean water to form a stiff paste and fill the void by pressing the paste into the damaged area for a minimum of 25 seconds for the pressurized water area & for the non pressurized water area apply the stiff paste in cracks and small holes & remove the hand which sets instantly. Once set remove excess material by cutting surface with a trowel or by scraper .

Views

  • 3314 Total Views
  • 2515 Website Views
  • 799 Embeded Views

Actions

  • 0 Social Shares
  • 2
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 5

  • 84 www.sab-us.com
  • 24 161.97.92.48
  • 157 www.google.com
  • 2 161.97.92.48:8011
  • 8

Website Visitors - 513932