VELOSIT® TDS-PC-222-EN_2319-1 (Plug Cement and Starter)

Public Channel / Data Sheets

+971600541110

https://wa.me/97172281030


Applica'on fields
VELOSIT PC 222 is a flash se2ng cement for
concrete and masonry. The product is used to
waterproof water leakages and as an accelerator for
other VELOSIT mortars. It is especially strong against
negaCve side water pressure. Typical applicaCon
fields besides others are as follows:
• Waterproofing of punctual water leakages for
example in concrete pipes, water tanks and
basement walls
• Set accelerator for VELOSIT repair mortars
Proper'es
VELOSIT PC 222 is a shrinkage compensated plug
cement with very fast strength development.
VELOSIT PC 222 sets within 10 – 15 seconds.
VELOSIT PC 222 is immediately waterproof and
anchors itself into the concrete surface.
VELOSIT PC 222 surpasses the requirements of EN
1504-3 class R2 for concrete repair (CR) and can be
used according to the principles 3.1 and 3.3 acc. to
EN 1504-9.
VELOSIT PC 222 can be applied by hand or trowel.
• Minimal shrinkage/expansion under dry resp.
wet curing condiCons
• Fast strength development with 12 MPa
compressive strength a[er 1 hours and final
strength of more than 40 MPa (5800 psi) a[er
28 days
• Resists 130 m (400 [.) water pressure acc. to EN
12390-8
• Flash se2ng with water
• Ready to receive top coat a[er 10 min.
• Ready for water pressure a[er a few minutes
• Very good adhesion to concrete and masonry
• No cracking
• No curing required
• Good resistance against aggressive media with a
pH range of 3-12 and against so[ water with
low ion content
• Good weathering resistance
• Potable water approved
• Good sulfate resistance

Applica'on
1.) Substrate prepara'on
VELOSIT PC 222 is designed for mineralic substrates
like concrete, masonry or absorpCve natural stones.
Chisel defecCve area or water leakage open
achieving a U-shaped profile. Remove all dust and
debris from areas to be treated. Dampen the surface
with water to a saturated surface dry (SSD) condiCon
before applicaCon of VELOSIT PC 222.
2.) Processing
VELOSIT PC 222 is applied as a dry powder into the
leakage. Due to the immediate set it is not possible
to mix the product with water.
a.) Plugging of water leakages: Apply a handful of
dry VELOSIT PC 222 (wear protecCve gloves!) into
the prepared leakage. Hold for 1 to 2 minutes unCl
the product has sufficiently hardened. Immediately
shave the surface flush with the substrate. A[er a
short waiCng Cme the area waterproofing with
VELOSIT WP 101 or CW 111 can be applied.
b.) Use as accelerator: VELOSIT PC 222 acts as an
accelerator for many cemenCCous mortars.
Required amount must be determined in trial mixes.
3.) Curing
VELOSIT PC 222 does not require curing.
Cleaning
VELOSIT PC 222 can be removed in the fresh state
with water. Once it has cured acidic cleaners like
muriaCc acid are required.
Quality features
Color: gray
Density: 1.2 kg/l
Substrate temperature: 5 – 35 °C
(40 – 95 °F)
Water impermeability acc. EN 12390-8:
- PosiCve side: 5 bar (190 psi)
- NegaCve side: 5 bar (72 psi)
Compressive / flexural strength:
1 hour: 12 / 2 MPa (1740/290 psi)
24 hours: 30 / 5 MPa (4350/725 psi)
7 days: 40 / 6 MPa (5800/870 psi)
Chloride ions: < 0.05 %
CarbonaCon resistance: passed
Capillary water absorpCon: 0.4 kg/m2 x h0.5
Adhesive strength: 1.2 MPa (232 psi
Restrained shrinkage: 1.2 MPa (218 psi)
Packaging
VELOSIT PC 222 is available in 12 kg (26 lb.) plasCc
pails.
Storage
VELOSIT PC 222 can be stored in unopened original
packs for 12 months at 5 – 35 °C (40 – 95 °F) in a dry
storage place protected against sunlight.
Safety
Please observe the actual valid material safety data
sheet and follow the described safety measures for

handling of the product.
Recommenda'ons
VELOSIT PC 222 is only available for professional
applicators.
Never add water to VELOSIT PC 222 when it has
started to set. SCffened material must be disposed.
All described product features are determined under
controlled laboratory condiCons according to the
relevant internaConal standards. Values determined
under job site condiCons may deviate from the
stated values.
Please always use the latest version of this data
sheet available from our website www.velosit.de.
Manufacturer
VELOSIT GmbH & Co. KG
Industriepark 7
32805 Horn-Bad Meinberg
Germany
www.velosit.de


UAE +600541110

+971 2 566 2610

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 

3. VELOSIT ® PC 222 handling of the product. Recommenda'ons VELOSIT PC 222 is only available for professional applicators. Never add water to VELOSIT PC 222 when it has started to set. SCffened material must be disposed. All described product features are determined under controlled laboratory condiCons according to the relevant internaConal standards. Values determined under job site condiCons may deviate from the stated values. Please always use the latest version of this data sheet available from our website www.velosit.de . Manufacturer VELOSIT GmbH & Co. KG Industriepark 7 32805 Horn-Bad Meinberg Germany www.velosit.de 2319 Page of 3 3 VELOSIT GmbH & Co. KG Industriepark 7 D-32805 Horn-Bad Meinberg 15 VELOSIT PC 222 DIN EN 1504-3 Product for non structural repair for concrete Compressive strength R2 Chloride ion content ≤ 0.05 % Adhesive bond ≥ 0.8 MPa Restrained shrinkage/ NPD expansion Reaction to fire E

1. VELOSIT ® PC 222 Applica'on fields VELOSIT PC 222 is a flash se2ng cement for concrete and masonry. The product is used to waterproof water leakages and as an accelerator for other VELOSIT mortars. It is especially strong against negaCve side water pressure. Typical applicaCon fields besides others are as follows: • Waterproofing of punctual water leakages for example in concrete pipes, water tanks and basement walls • Set accelerator for VELOSIT repair mortars Proper'es VELOSIT PC 222 is a shrinkage compensated plug cement with very fast strength development. VELOSIT PC 222 sets within 10 – 15 seconds. VELOSIT PC 222 is immediately waterproof and anchors itself into the concrete surface. VELOSIT PC 222 surpasses the requirements of EN 1504-3 class R2 for concrete repair (CR) and can be used according to the principles 3.1 and 3.3 acc. to EN 1504-9. VELOSIT PC 222 can be applied by hand or trowel. • Minimal shrinkage/expansion under dry resp. wet curing condiCons • Fast strength development with 12 MPa compressive strength a[er 1 hours and final strength of more than 40 MPa (5800 psi) a[er 28 days • Resists 130 m (400 [.) water pressure acc. to EN 12390-8 • Flash se2ng with water • Ready to receive top coat a[er 10 min. • Ready for water pressure a[er a few minutes • Very good adhesion to concrete and masonry • No cracking • No curing required • Good resistance against aggressive media with a pH range of 3-12 and against so[ water with low ion content • Good weathering resistance • Potable water approved • Good sulfate resistance 2319 Page of 1 3 VELOSIT ® PC 222 Plug Cement And Starter

2. VELOSIT ® PC 222 Applica'on 1.) Substrate prepara'on VELOSIT PC 222 is designed for mineralic substrates like concrete, masonry or absorpCve natural stones. Chisel defecCve area or water leakage open achieving a U-shaped profile. Remove all dust and debris from areas to be treated. Dampen the surface with water to a saturated surface dry (SSD) condiCon before applicaCon of VELOSIT PC 222. 2.) Processing VELOSIT PC 222 is applied as a dry powder into the leakage. Due to the immediate set it is not possible to mix the product with water. a.) Plugging of water leakages: Apply a handful of dry VELOSIT PC 222 (wear protecCve gloves!) into the prepared leakage. Hold for 1 to 2 minutes unCl the product has sufficiently hardened. Immediately shave the surface flush with the substrate. A[er a short waiCng Cme the area waterproofing with VELOSIT WP 101 or CW 111 can be applied. b.) Use as accelerator: VELOSIT PC 222 acts as an accelerator for many cemenCCous mortars. Required amount must be determined in trial mixes. 3.) Curing VELOSIT PC 222 does not require curing. Cleaning VELOSIT PC 222 can be removed in the fresh state with water. Once it has cured acidic cleaners like muriaCc acid are required. Quality features Color: gray Density: 1.2 kg/l Substrate temperature: 5 – 35 °C (40 – 95 °F) Water impermeability acc. EN 12390-8: - PosiCve side: 5 bar (190 psi) - NegaCve side: 5 bar (72 psi) Compressive / flexural strength: 1 hour: 12 / 2 MPa (1740/290 psi) 24 hours: 30 / 5 MPa (4350/725 psi) 7 days: 40 / 6 MPa (5800/870 psi) Chloride ions: < 0.05 % CarbonaCon resistance: passed Capillary water absorpCon: 0.4 kg/m 2 x h 0.5 Adhesive strength: 1.2 MPa (232 psi Restrained shrinkage: 1.2 MPa (218 psi) Packaging VELOSIT PC 222 is available in 12 kg (26 lb.) plasCc pails. Storage VELOSIT PC 222 can be stored in unopened original packs for 12 months at 5 – 35 °C (40 – 95 °F) in a dry storage place protected against sunlight. Safety Please observe the actual valid material safety data sheet and follow the described safety measures for 2319 Page of 2 3   



  #"% (# *' !")$(# &'%"% )!' *' $+ !&$ -"*!    2 *' ,$ -"*!   *' &* -"*!   CW 

Views

  • 4644 Total Views
  • 3662 Website Views
  • 982 Embeded Views

Actions

  • 0 Social Shares
  • 2
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 5

  • 3 www.sab-cs.com
  • 26 161.97.92.48
  • 1 sab-cs.com
  • 102 www.sab-us.com
  • 2 161.97.92.48:8011

Website Visitors - 487879