Nitoflor anti-slip grains are designed for use with
Nitoflor/Trafficguard resin based products to produce non-slip
industrial floors. Ideally suited for wet wok areas in abattoirs,
breweries, dairies, chemical industries, food processing
areas, loading bays, car parks, ramps and walkways.
Advantages
Range of products to suit most applications
Special gradings to suit Nitoflor products
Pre-packed ready for immediate site use
1. Al Gurg Fosroc LLC Post Box 6 57, Dubai United Arab Emirates www.fosroc.com telephone : fax: email: (+9714) 2039699 (+9714) 2859649 agf@fosroc.com Registered Office: 215 Community, Street No. 13, Nad Al Hamar Road, Al Ramool Industrial Estate, Rashidiya, Dubai Page 1 Fosroc Nitoflor Anti - Slip grains ME / 22012 /1 1 / C Important note Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions fo r the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or cont inuous control over w here or how its products are applied, accept any liability either directly or indirectly arising from the use of its products , whether or not in accordance with any advice, specification, recommendation or information given by it. Constructive solutions Non - slip flooring aggregates Uses Nitoflor anti - slip grains are designed for use with Nitoflor /Trafficguard resin based products to produce non - slip industrial floors. Ideally suited for wet wok areas in abattoirs, breweries, dairies, chemical industries , food processing areas, loading bays, car parks, ramps and walkways. Advantages Range of products to suit most applications Special grading s to suit Nitoflor products Pre - packed ready for immediate site use Description Nitoflor anti - slip grain No 1 Spe cially selected, hard wearing, chemically inert aggregate of road stone quality for use with Nitoflor SL and Trafficguard range to provide a coarse textured, non - slip floor topping. Nitoflor anti - slip grain No 2 Chemically inert, graded, hard wearing aggr egate for use with Nitoflor FC150 , Trafficguard and SL range to produce a medium coarse textured floor finish. Nitoflor anti - slip grain No 3 Finely graded, chemically inert aggregate for use with Nitoflor FC150 and SL range to produce a non - slip floor wit h a fine textured finish. Nitoflor Antislip grain No 4 Extra fine, chemically inert aggregate for use only with Nitoflor FC130 or Nitoflor FC140 to provide a fine textured non - slip finish with thin floor coatings Nitoflor Antislip grain No 1200 Specially selected, graded, chemically inert aggregate for use with Trafficguard System and SL range to produce an Antislip finish. Application instructions All Nitoflor anti - slip grains should be clean and dry prior to application. Nitoflor Antislip grains No1, N o2 and No3 are designed for use with Nitoflor FC150, solvent free, resin based, roller applied floor coatings, Trafficguard Systems and Nitoflor SL range. In case of application onto SL products a final coat of Nitoflor FC150 is applied Nitoflor Antislip grain No 4 is used in conjunction with Nitoflor FC130 and Nitoflor FC140 floor coatings. When using anti - slip grain No 4, the resultant floor finish will be of a fine texture the thickness of which will range from 0.3 to 0.6mm. Application The specially graded aggregates are scattered on the first rolled coat of Nitoflor resin or primer coat while it is still wet. Sufficient Nitoflor anti - slip grains should be applied to completely cover or blind the surface. The selected anti - slip grain should be allo wed to fall vertically onto the resin coating rather than be thrown across the surface as this may cause ridges or scour the coatings and damage the continuous film of the resin flooring. When the first coat has dried, the excess aggregate can be brushed or vacuumed off the substrate and provided it is still clean and dry can be re - used. The final coat can then be applied to produce a hard wearing, chemically resistant non - slip floor. The texture and thickness of the floor is determined by the choice of t he Nitoflor anti - slip grains. Nitoflor Anti - slip grains Finished Texture Antislip grain size(maximum) No 1 Coarse 2.5mm No 2 Medium 1.0mm No 3 Fine - medium 0.5mm No 4 Fine 0.3mm No 1200 Medium coarse 1.2mm Estimation Supply Nitoflor anti - slip grain s : 25 kg bags Approximate usage 0.4 to 0.8 kg/m 2 = 1.25 to 2.5 m 2 /kg Storage Store in dry conditions in original, unopened packs Precautions Health and safety Nitoflor anti - slip grains are non - hazardous. Fire Nitoflor anti - slip grains are non - flamma ble
Views
- 3278 Total Views
- 2405 Website Views
- 873 Embeded Views
Actions
- 0 Social Shares
-
2
-
0
- 0 Comments
Share count
-
0
Facebook
-
Twitter
-
0
LinkedIn
Embeds
3
-
15
161.97.92.48
-
103
www.sab-us.com
-
1
161.97.92.48:8011