2. TDS - WP - NB01 - 000_01/21 Properties Value Norm Reinforcement Double reinforcements Test Method Weight of reinforcements Min. 240 g/m2 EN 29073 Board Size/Weight Thickness Nominal thickness 3.0 mm 4.0 mm 5.0 mm 6.0 mm EN 1849 Nominal weight 9 k g 12 k g 15 k g 18 k g EN 1849 Board Dimensions 2 m X 1 m EN 1848 Mechanical Properties Tensile Strength (Longitudinal) 700 N/5cm 800 N/5cm 900 N/5cm 1000N/5cm EN 12311 Tensile Strength, (Transversal) 700 N/5cm 750 N/5cm 750 N/5cm 80 0 N/5cm EN 12311 Tear Resistance, (Longitudinal) 550 N 600 N 700 N 700 N ASTM D 5147 Tear Resistance, (Transversal) 500 N 550 N 600 N 600 N ASTM D 5147 Puncture Resistance Static Puncture Resistance 15 kg 20 kg 25 kg 30 k g EN 12730 A Dynamic Puncture Resistance 500 mm 600 mm 700 mm 800 mm EN 12691 B Additional Characteristics Water tightness Impermeable to water (100 kpa) EN 1928 Softening point > 150 ⁰c ASTM D 36 Salt Resistance Excellent Water absorption Max. 1 % ASTM D 5147 All values are subject to 5 - 10 % tolerance TECHNICAL CH ARACTERISTICS NOTE: The information contained in this DATA SHEET, as well as our advice, both written as oral or provided through testing, are based on our experience, and they do not constitute any product guarantee for the installer, who must take them as simple orientations, provided strictly as informatio n. We recommend to study deeply all information provided before proceeding to the use or application of any of our products, and strongly advise to conduct tests “on - site” in order to determine their convenience for a specific project. Our recommendations do not exempt of the obligation that installers have to deeply know the right application method for these systems before they use them, as well as to conduct as many preliminary tests as possible if there are any doubts about the appropriate system to use . The application, use and processing of our products are beyond our control, and therefore under the exclusive responsibility of the installer. In consequence, the installer will be the only responsible of any damage or prejudice derived from the partial or total in - observation of our indications, and in general, of the inappropriate use or application of these materials. Sajaa Industrial Area behind Sharjah Cement Factory, Sharjah U.A.E. Email: info@royalwayindustries.com PO BOX: 65034 Tel: +971 6 572 6378 Website: www.royalwayindustries.com R OYAL WAY INDUSTRIES LLC Page 2

1. TDS - WP - NB01 - 000_01/21 PROPRETIES C H AR A C TERISTICS NEOBOARD is a tou gh, semi - flexible prefabricated protection board, composed of mineral fortif ied bituminous core, held under pressur e between two asphalt saturated carriers. NEOBOARD Bituminous Protection Board Page 1 NEOBOARD is used as a protection layer over water proofing applications on bridge decks, parking garage decks, terraces, tunnels, foun dation walls and slabs, and wet room floors. The tough durable nature of the product makes it ideally suited to withstand t he shock and impa ct of backfilling and paving as well as normal on - site traffic, concreting, or other toppings. USES  Protect waterproofing against construction traffic, other trades, and impact of back fill soil.  Compatible with almost all waterproofing membranes such as bituminous, EPDM, TPO, PVC and coatings such as acrylic, polyurethane, epoxy and others.  Resistant to salts and chemicals normally found in soil (Chlorides, Sulphates, and Phosphates).  Rot - proof, un - affected by emersion in ground water, and impervious to water.  Excellent resistance to puncture & normal site conditions.  Can bridge over gravel embedded roof surfaces, and can be bent to normal contours while maintaining rigidity, due to being semi flexible. FEATURES VERTICAL APPLICATION Protection boa rd is temporarily held in place by sp ot bonding to the waterproofing membrane using hot asphalt or compatible adhesive. Stagger joints a minimum of 15 cm and overlap boards approximately 1cm - 2.5cm. Cover joints with joint tape to prevent backfill partic les from damaging the membrane. Backfill immedia tely, using care and caution to avoid damage to waterproofing system. FORM OF SUPPLY & STORAGE NEOBOARD is supplied in sheets 1M X 2 M in standa rd thicknesses 3mm, 4mm, 5mm and 6mm. Boards s hould be kept stored in pallets placed on level surfaces under shade or cover. Stack no more than two pallets high. Product Boards/ Pallet NEOBOARD 3.0 mm 225 NEOBOARD 4.0 mm 150 NEOBOARD 5.0 mm 125 NEOBOARD 6.0 mm 100 Loading Capacity: 10 pallets/ 20’ Container The surface to receive the protection board is normally o ne which has been waterproofed. The waterproo fed surface must be clean, free of any debris, or sharp protrusions. Apply NEO BOARD protection board directly on the waterproofing membrane as soon as practicable. APPLICATION Butt together all protection board panels and cut to fit all intersecting and protruding surfaces. Cover joi nts with joint tape if desired. Ensure subseq uent ballast layers are applied as soon as poss ible following protection board application. HORIZONTAL APPLICATION