Public Channel / Data Sheets

PVA Bonding Agent

SAB® spadbond PVA 218:
Is an opaque aqueous white liquid, externally plasticized polyvinyl acetate emulsion of medium to high viscosity. It is an aqueous emulsion specially formulated for use as a bonding agent and as an additive with cementitious mixes to improve the mix properties.

SAB® spadbond PVA 218 is used in cementitious mortars, plasters, concrete, thin layer patch mortars, etc. to improve the waterproofing, wear resistance, durability and bonding properties.

ADVANTAGES
As Bonding Agent: SAB® spadbond PVA 218 will bond cement screeds, rendering and plaster to most sound surfaces such as concrete, stone and brick and new concrete to old without the need for hacking the surface to form a key. As Admixture: As an admixture in cements/sand and granolithic screeds:


PREPARATION OF SURFACE
MIXING
As a Bonding Slurry Coat: As per recommended dosage, add SAB® spadbond PVA 218 to premeasured quantity of water in a suitable container and stir well. Add cement slowly and mix well using a slow speed drill machine fitted with a paddle.
As an Admixture: Manual mixing is not recommended. Preferably a forced action mixer or low speed drill fitted with a paddle should be used. Weigh the cement and sand where required, into the mixer and dry blend together for one minute. Add the premixed SAB® spadbond PVA 218 and clean water. Continue mixing for 3 minutes to ensure complete dispersal into the sand-cement mix. Make any small adjustment to the quantity of clean water but do not significantly exceed the dosage shown below. Mix until homogenous material is obtained.
Repair Mortar Mix Proportions
Thickness 6 -40mm
10 litres of SAB® spadbond PVA 218
8-12 litres of water (as per the required consistency).
50 kg of Ordinary Portland cement
150 kg of sand.
Floor Screed- Mix Proportions
Thickness:30mm- 70 mm
10 liters of SAB® spadbond PVA 218
6-10 liters of clean water
50 kg of Ordinary Portland Cement 100 kg of fine aggregate.
The screed should be of earth moist consistency.
Renders-Mix Proportions
Thickness: 6mm -15mm
10 liters. Of SAB® spadbond PVA 218
6-10 ltrs of clean water
50 kg of Ordinary Portland Cement
100 kg of fine sand
The render should be cohesive and of earth moist consistency.


CURING
All cementitious mortars, render, screeds, repair materials modified with SAB® spadbond PVA 218 should be cured with mist water spray or moist curing by spreading wet hessian cloth or use of appropriate curing compound from ECOCURE range.


COVERAGE
As a neat bonding agent: 5-7 m²/litre/coat. Actual coverage depends on texture and porosity of substrate. As an additive for tile and adhesives, bedding mortars, sand-cement renders plasters and screeds. The dosage may vary from 10-20% by weight of cement.


PACKING AND STORAGE
5 Litres, 20 Litres & 200 Litres Drums

STORAGE AND SHELF LIFE
Store under cover, out of direct sunlight and protect from extremes of temperature. Storage life up to 12 months when stored in unopened containers as above. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.
when stored in unopened containers as above. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging.

SHELF LIFE
12 months when stored as above.

Share on Social Networks

Share Link

Use permanent link to share in social media

Share with a friend

Please login to send this document by email!

Embed in your website

Select Link to start with 

3. Admix 218 should be cured with mist water spray or moist curing by spreading wet hessian cloth or use of appropriate curing compound from ECOCURE range. COVERAGE As a neat bonding agent: 5 - 7 m²/litre/coat. Actual coverage depends on texture and porosity of substrate. As an additive for tile and adhesives, bedding mortars, sand - cement renders plasters and screeds. The dosage may vary from 10 - 20% by weight of cement. HEALTH AND SAFETY As with all chemical products. Care should be taken during use and storage. Spillages of SAB ® bond ing PVA Admix 218 should be absorbed onto sand, earth or vermiculite and transferred to suitable containers. Contaminated areas will become slippery therefore care must be exercised. The disposal of excess or waste material should be carried out in accordan ce with local legislation under the guidance of the local waste regulatory authority. PACKING AND STORAGE 5 Litres, 20 Litres & 200 Litres Drums STORAGE AND SHELF LIFE Store under cover, out of direct sunlight and protect from extremes of temperature. Storage life up to 12 months when stored in unopened containers as above. Failure to comply with the recommended storage conditions may result in premature deterioration of the product or packaging. SHELF LIFE 12 months when stored as above.

1. SAB ® bonding PVA Admix 218 PVA Bonding Agent Description SAB ® bond ing PVA Admix 218 : Is an opaque aqueous white liquid, externally plasticized polyvinyl acetate emulsion of medium to high viscosity. It is an aqueous emulsion specially formulated for use as a bonding agent and as an additive with cementitious mixes to improve the mix proper ties. SAB ® bond ing PVA Admix 218 is used in cementitious mortars, plasters, concrete, thin layer patch mortars, etc. to improve the waterproofing, wear resistance, durability and bonding properties. ADVANTAGES As Bonding Agent: SAB ® bond ing PVA Admix 218 will bond cement screeds, rendering and plaster to most sound surfaces such as concrete, stone and brick and new concrete to old without the need for hacking the surface to form a key. As Admixture: As an admixture in cements/sand and granolithic screeds: Technical data SAB ® bond ing PVA Admix 218 Appearance White Liquid Solid Content 35% Specific Gravity 0.98 to 1.02 (All values are subject to 5 - 10 % tolerance). PREPARATION OF SURFACE MIXING As a Bonding Slurry Coat: As per recommended dosage, add SAB ® bond ing PVA Admix 218 to premeasured quantity of water in a suitable container and stir well. Add cement slowly and mix well using a slow speed drill machine fitted with a paddle. As an Admixture: Manual mixing is not recommended. Preferably a forced action mixer or low

2. speed drill fitted with a paddle should be used. Weigh the cement and sand where required, into the mixer and dry blend together for one minute. Add the premixed SAB ® bond ing PVA Admix 218 and clean water. Continue mixing for 3 minutes to ensure complete dispersal into the sand - cement mix. Make any small adjustment to the quantity of clean water but do not significantly exceed the dosage shown below. Mix until homogenous material is obtained. Repair Mortar Mix Proportions Thickness 6 - 40mm 10 litres of SAB ® bond ing PVA Admix 218 8 - 12 litres of water (as per the required consistency). 50 kg of Ordinary Portland cement 150 kg of sand. Floor Screed - Mix Proportions Thickness:30mm - 70 mm 10 liters of SAB ® bond ing PVA Admix 218 6 - 10 liters of clean water 50 kg of Ordinary Portland Cement 100 kg of fine aggregate. The screed should be of earth moist consistency. Renders - Mix Proportions Thickness: 6mm - 15mm 10 liters. Of SAB ® bond ing PVA Admix 218 6 - 10 ltrs of clean water 50 kg of Ordinary Portland Cement 100 kg of fine sand The render should be cohesive and of earth moist consistency. APPLICATION AND CLEANING OF TOOLS As a Neat Bonding Agent : Stir SAB ® bond ing PVA Admix 218 well and apply using brush, roller or spray on the prepared surface. Ensure that the material is spread evenly on the entire surface. Subsequent material to be bonded should be placed while SAB ® bond ing PVA Admix 218 is still tacky. As a Bonding Slurry Coat : Apply slurry bonding coat made up of SAB ® bond ing PVA Admix 218 , water and cement into the ration of 1:1:1 by weight using brush or roller. As an additive : SAB ® bond ing PVA Admix 218 modified mortars, toppings and renders must be well compacted on the prepared substrate by trowel. Exposed steel reinforcement should be completely encapsulated by mortar. SAB ® bond ing PVA Admix 218 modified mortars can be applied at a thickness of 6 mm to 40 mm. Where thick sections in excess of 40mm are to be built up, the surface of the intermediate layers should be keyed and primed. CURING All cementitious mortars, render, screeds, repair materials modified with SAB ® bond ing PVA

Views

  • 2372 Total Views
  • 1775 Website Views
  • 597 Embeded Views

Actions

  • 0 Social Shares
  • 4
  • 0
  • 0 Comments

Share count

  • 0  Facebook
  • 0  Twitter
  • 0  LinkedIn

Embeds 5

  • 16 www.sab-us.com
  • 18 161.97.92.48
  • 5 161.97.92.48:8011
  • 154 www.google.com
  • 8

Website Visitors - 505949